Vivo STAND-V001O User manual

Pneumatic Arm Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001o
SKU: STAND-V001O
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
4.4-19.8lbs
(2-9kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PACKAGE CONTENTS
A (x1)
Gas Spring
Arm
B(x1)
Bracket
C(x1)
Clamp
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
S-C (x3)
M6x12mm
Screw
S-D (x2)
M6x10mm
Screw
F (x1)
Grommet
Base
S-A (x1)
Carriage Bolt
H (x1)
Support Plate
M-A (x4)
M4x12mm
Screw
M-B (x4)
M5x12mm
Screw
S-B (x1)
Wing Nut
T-B (x1)
4mm Allen Wrench
M-C (x4)
M5 Washer
T-A (x1)
5mm Allen Wrench
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS
STEP 2
OPTION A: Clamp Installation
Mount Bracket (B) to bottom of Gas Spring Arm (A) using M6x12mm Screws (S-C). Tighten using
4mm Allen Wrench (T-A). Attach Clamp (C) to Bracket (B) using M6x10mm Screws (S-D) and 4mm
Allen Wrench (T-A). Install according to thickness of desktop as shown in diagrams. Secure stand
to desktop by tightening Clamp (C).
STEP 1
Remove Gas Spring Arm (A) from packaging. While holding arm closed, cut the
shipping tie and gently release arm.
S-C
T-A
S-D
S-D
T-A
T-A

4
STEP 2 (Continued)
OPTION B: Grommet Base Installation
For grommet hole mounting, place Carriage Bolt (S-A) through
the center of Grommet Base (F). Mount Grommet Base to bottom
of Gas Spring Arm (A) using M6x12mm Screws (S-C). Tighten
using 4mm Allen Wrench (T-A). Run Carriage Bolt (S-A) through
grommet hole in desktop. If no grommet hole is present, drill
hole using a 3/8” (10mm) drill bit. Attach Support Plate (H) and
Wing Nut (S-B) to Carriage Bolt (S-A). Tighten Wing Nut (S-B) to
secure.
STEP 3
Attach two Screws (M-A or M-B) and
M5 washers (M-C) to top mounting
holes of monitors, making sure to leave
3mm of threads exposed. Align Screws
(M-A, M-B) in VESA plate. Secure using
two more Screws (M-A or M-B) and M5
Washers (M-C) in the bottom two holes.
Tighten all four screws using Phillips
screwdriver end of 5mm Allen Wrench
(T-B).
T-A
S-C
S-A S-B
T-B

5
STEP 4
Adjust tension in Gas Spring Arm (A) using 5mm Allen Wrench (T-B). Turning clockwise decreases
strength, and counter-clockwise increases.
T-B
WARNING:
Monitor must be installed on mount
before making tension adjustments to the
gas spring arm.
Keep monitor in a straight orientation
when making adjustments.

6
STEP 5
Remove bottom plastic covers from Gas Spring Arm (A) using Phillips screwdriver end of 5mm Allen
Wrench (T-B). Run cables from monitor through bottom of Gas Spring Arm (A), then reattach plastic
covers.
T-B
T-B

7
STEP 6
Adjust monitor tilt support using 5mm Allen Wrench (K) as shown.
Adjust monitor position as desired.
T-B

LAST UPDATED: 02/01/2023
REV2.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303