Vivo STAND-V001T User manual

Single Monitor Extra Tall Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001t
SKU: STAND-V001T
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Arm
B(x1)
Bottom Pole
C(x1)
Top Pole
M-A (x4)
M4x12mm Screw
J (x1)
Support Plate
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Clamp
E(x1)
Grommet Plate
F (x1)
Pole Connector
G(x2)
Cable Clip
H (x1)
Pole Cap
I (x5)
So Pad
M-C (x4)
M5 Washer
M-B (x4)
M5x12mm Screw
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
T-A (x1)
3mm Allen Wrench
S-A (x3)
M6x16mm Screw
T-B (x1)
4mm Allen Wrench
T-C (x1)
5mm Allen Wrench
T-D (x1)
6mm Allen Wrench

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Install Clamp (D) to Bottom Pole (B) using M6x16mm Screws (S-A) and tighten using 3mm Allen Wrench
(T-A). Remove the adhesive backing from So Pads (I) and place them on the underside of Clamp (D).
Mount Clamp (D) to the desktop and tighten the knob.
TOOLS NEEDED
22lbs
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
OPTION B: Grommet Hole Installation
Disassemble Clamp (D) into individual parts. Remove Clamp Plate (D1) (You will not
need this for Grommet installation) using Phillips screwdriver and remove Knob (D2).
Remove the adhesive backing from So Pads (I) and place them on the underside of
Grommet Plate (E).
D
B
S-A
T-A
I
D2
D1
T-B

4
STEP 1 (Continued)
Slide Cable Clips (G) onto Bottom Pole (B) and Top Pole (C). Use the Pole Connector (F) to attach Top
Pole (C) to Bottom Pole (B). Tighten the set screws on Pole Connector (F) using 3mm Allen Wrench
(T-A). Insert Pole Cap (H) into the top of Top Pole (C).
STEP 2
OPTION B: Grommet Hole Installation
Place Bottom Pole (B) ontop of Grommet Plate (E). Secure to the desktop using Knob (D2) and
Support Plate (J).
B
E
D2
T-A
B

5
STEP 3
Install Screws (M-A or M-B) and M5 Washers (M-C) to the top mounting holes of your
monitor, making sure to leave 3mm of threads exposed. Align Screws (M-A or M-B) in the
VESA plate. Secure using two more Screws (M-A or M-B) and M5 Washers (M-C) in the
bottom two holes. Tighten all four screws using a phillips screwdriver.
Loosen the screw on the back of Arm (A) using 5mm Allen Wrench (T-C). Slide Arm (A) over the top of
Top Pole (C). Retighten the screw on Arm (A) using the 5mm Allen Wrench (T-C).
STEP 4
C
T-C

6
STEP 5
Adjust the tension in the monitor bracket with 6mm Allen Wrench (T-D)as shown in diagram.
STEP 6
Store Allen Wrenches (T-C, T-D) in Cable Clip (G) for future adjustment.
T-D
G
T-C
T-D

7
Adjust as Desired

LAST UPDATED: 04/13/2022
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303