Vivo STAND-V002 User manual

Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002
SKU: STAND-V002
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Pole
B(x1)
Clamp
C(x1)
Clamp Brace
L2 (x4)
Wire Clip
M(x1)
Allen Key Set
O(x8)
M4x30 Bolt
L1 (x1)
Wire Clip
I (x1)
M10 Washer
J (x1)
Spring Washer
K (x1)
Grommet
Base Plate
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
Q1 (x1)
So Pad
P(x8)
M4 Spacer
D(x1)
Swivel Arm
E(x2)
VESA Plate
F (x3)
M5x14 Bolt
G(x2)
M8x12 Bolt
H (x2)
Nut
N(x8)
M4x12
Thumbscrew
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Q2 (x1)
So Pad

3
ASSEMBLY STEPS
STEP 1
Option A: Desk Clamp Install
1. Install the clamp brace (C) to the pole (A) using x3 M5x14 bolts (F). See Figure 1.
2. Attach so pad (Q1) to the clamp brace (C) , see Figure 2.
3. Install the clamp (B) to the pole assembly according to the thickness of the desktop. The
thickness can be changed to 3 positions. Connect using x2 M8x12 bolts (G) and tighten using the
Allen wrench (M). Tighten the clamp to the desktop using the plastic knob. See Figure 3.
TOOLS NEEDED
22 lbs
Per Arm
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
Option B: Grommet Install
1. If desk does not have an existing grommet
hole, drill a 3/8” (10mm) diameter hole at the
desired position through the mounting surface.
2. Completely disassemble clamp (B) into
individual parts. Set knob (B1) and clamp
plate (B2) aside for later use. The L bracket,
bolt, washer and bushing will not be used.
3. Install grommet base plate (K) to the pole (A)
using x3 M5x14 bolts (F). See Figure 4.
4. Attach so pad (Q2) to the grommet base plate
(K), see Figure 5.
5. Position pole (A) on the mounting surface
and secure using the clamp plate (B2), spring
washer (J), M10 washer (I) and knob (B1). See
Figure 6.
a
Figure 1 Figure 2
B1
B2
B2
B1
a
m
f
Figure 4
t2 Figure 5
a
m
f
Figure 4
t2 Figure 5
Q1
F
C
A
A
K
M
G
B
J
I
Q2
F

4
STEP 2
Install swivel arm (D) to the pole (A). Fasten the bolt with supplied Allen wrench (M). Attach the wire
clip (L1,L2) to the pole (A) and swivel arm (D).
STEP 3
OPTION A: Flat Back Monitor
Attach the VESA plate (E) to the monitor with
M4x12 thumbscrews (N).
NOTE: Hand tighten screws to avoid over
tightening.
OPTION B: Curved Back Monitor
Attach the VESA plate (E) to the monitor with
M4x30 bolts (O) and M4 spacers (P).
NOTE: Gently tighten using a screwdriver
M
L1
L2
D
NP
O

5
Slide the monitor onto the head of swivel arm (D).
STEP 4
Install the security nut (H). Make sure the security nut is installed before you rotate the monitor. For
minor height adjustment, use Allen wernch (M).
H

6
STEP 5
Tighten the bolt with the supplied Allen wrench (M) to fix the tilt angle.
To level the monitors, remove the nut (H) and turn the bolt with the Allen wrench (M) to raise or lower
the monitor. Replace nut (H) aer the adjustment.
M
M

7
STEP 6
Use the supplied Allen wrench set (M) to make any necessary adjustments. Manage cables and store
Allen wrenches (M) in wire clip (L1) for future use.
o
M
L1

LAST UPDATED: 03/09/2021
REV1.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303