Vivo STAND-V101G2 User manual

Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101g2
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V101G2

2 3
ASSEMBLY STEPS
STEP 1
Option A: Clamp Installation
Attach clamp brace (K) to base (A)
using at head bolts (M) and tighten
with 4mm Allen wrench (S). Apply
so pad (I) to underside of base.
Install short bolts (N) to back of clamp
(L), leaving 6mm of thread exposed.
Screw clamp bolts (Q) into underside
of clamp using 6mm Allen wrench (T).
For a desk thickness of 3/8” - 2-21/2”
(10 - 58mm), hang assembled clamp
into top 4 slots of clamp brace, or
for a desk thickness of 2” - 3-3/8”
(50 - 85mm), into lower 4 slots. Place
clamp plate (G) on top of clamp bolts.
Position base on desktop and tighten
clamp bolts evenly using 6mm Allen
wrench. Attach cover (J) to back of
clamp brace.
TOOLS NEEDED
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1)
Base
B(x2)
Lower Arm
C(x2)
Gas Spring Arm
Q (x2)
Clamp Bolt
R (x1)
3mm Allen
Wrench
P(x2)
Pan Head
Bolt
L (x1)
Clamp
M (x4)
Flat Head
Bolt
N (x4)
Short Bolt
O (x2)
Bolt
M-A (x8)
M4x12
E(x2)
VESA Plate
G(x1)
Clamp Plate
H (x1)
Grommet
Plate
I(x1)
So Pad
J (x1)
Cover
K (x1)
Clamp
Brace
M-B (x8)
M5x12
M-C (x8)
D5 Washer
D(x1)
Monitor Arm
F (x1)
Handle
T (x1)
6mm Allen
Wrench
S(x1)
4mm Allen
Wrench
A
KM
S
I
G
10-58mm
6mm
N
L
S
T
Q
50-85mm
G
6mm
N
L
S
T
Q
T
J
33 lbs
(15 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM

4 5
STEP 1 (Continued) STEP 4
Install the VESA plates (E) to monitors using M4x12 bolts (M-A) or M5x12 bolts (M-B) with
washers (M-C), making sure the arrow in back is pointing up.
Option B: Grommet Base Installation
Attach grommet plate (H) to base (A) using at head bolts (M) and tighten with 4mm Allen wrench
(S). Apply so pad (I) to underside of base. Position base over grommet hole in desktop, or drill a 3/8”
(10mm) hole through the desk for installation. Insert clamp bolt (Q) with clamp plate (G) up through
the underside of the desk and tighten to the base using the 6mm Allen wrench (T).
STEP 2
STEP 3
Place lower arm (B) on top of base, and secure by turning the lower screw in back with 3mm Allen
wrench (R). Optionally, also tighten the upper screw to restrict swivel movement to +/-90 degrees.
Place gas spring arm (C) on top of lower arm, and secure by turning the screw in back with 3mm Allen
wrench.
STEP 5
Mount handle (F) to back of monitor arm using pan head bolts (P) to one of the positions shown in the
diagram according to the size of your monitors. Tighten with 4mm Allen wrench.
STEP 6
TV
TV
TV
Install monitor arm (D) to gas spring arm using bolts (O) and tighten with 4mm Allen wrench.
H
M
S
I
G
T
Q
B±180 ° ±90 °
R
R
or
C
R
S
D
O
a
b
c
S
P
F
M- A
M- B
M- C

6 7
STEP 7 STEP 10
For safety, please do not extend the monitor behind the desk. This may cause instability and tip the
desk over.
Adjust as Desired
Place the monitors with VESA plates into the supports on the arm, then turn
the screw on each support to secure the monitors.
STEP 8
If needed, adjust gas spring arm to support the monitors using the 6mm Allen wrench. Turn the
screw in back clockwise to decrease support, and counter-clockwise to increase. Slightly loosen the
monitor arm for leveling if needed.
STEP 9
Remove cable cover on upper arm using a Phillips screwdriver. Slide cable cover on lower
arm forward to remove.
Organize cables, then reinstall cable covers to arms.
STEP 11
T
S
-4°
+4°
+10°
-10°
±90°/180°
-4°
+4°
±90°
±180°
TSR
±10°
±180°

Last Updated: 12/03/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654