Vivo STAND-V012C User manual

Single Monitor and Laptop Extra Tall Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v012c
SKU: STAND-V012C
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
a (x3)
Pole
b(x1)
Clamp
c(x1)
Clamp Brace
j (x1)
Support Plate
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
d(x2)
Swivel Arm
e(x2)
VESA Plate
f (x3)
M5x14
g (x2)
M8x12
h (x2)
Security Nut
i (x1)
M10 Bolt
k (x1)
M10 Washer
o (x1)
Allen Key
l (x1)
Spring Washer
m (x1)
Grommet Base
Plate
n1 (x3)
Cable Clip
p (x1)
Wrench
t (x1)
Laptop Tray
q (x8)
M4x12
r (x8)
M4x30
s (x8)
M4 Spacer
u (x4)
M4x10 Bolt
v (x4)
M4 Nut
n2 (x4)
Cable Clip
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
w1 (x1)
So Pad
w2 (x1)
So Pad

3
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
PRE-ASSEMBLY
Remove the grub screws by provided Allen Key (o). Connect the poles by threads as below diagram.
Install the grub screws and fasten them by provided Allen Key (o).
STEP 1
TOOLS NEEDED
Phillips
Screwdriver Drill
OPTION A: Clamp Installation
1. Install the “C” Clamp Brace (c) to the Pole (a)
using 3pcs M5x14 Bolts (f), and tighten using
the Allen Key (o), see Figure 1.
2. Attach So Pad (w1) to the “C” Clamp Brace
(c), see Figure 2.
3. Install the “C” Clamp (b) to the pole assembly
according to the thickness of the desktop. The
thickness can be changed to three positions.
Connect it using 2pcs M8x12 Bolts (g), and
tighten using the Allen Key (o). Tighten the
“C” Clamp (b) to the desktop using the plastic
knob, see Figure 3.
g
o
b
Plastic Knob
a
c
f
Figure 1
Figure 3
w1
Figure 2

4
STEP 1 (Continued)
OPTION B: Existing Grommet Base Installation
1. If the existing grommet hole comes with a
plastic protector, remove it to ensure a flat
surface before installing the desk mount.
Install the Grommet Base Plate (m) to the Pole
(a) using 3pcs M5x14 Bolts (f), and tighten
using the Allen Key (o), see Figure 4.
2. Attach So Pad (w2) to the Grommet Base
Plate (m), see Figure 5.
3. Position the Pole (a) on the mounting surface
and secure using the Support Plate (j), M10
Washer (k), Spring Washer (l) and M10 Bolt (i).
Fasten the M10 Bolt using provided Wrench (p),
see Figure 6.
j
i
k
l
a
m
f
Figure 4
Figure 6
w2 Figure 5
OPTION C: Self-Drilled Grommet Base Installation
1. Position the Pole (a) on the mounting surface
and mark the center hole. Drill a 3/8” (10mm)
diameter hole at the marked position through
the mounting surface. Install the Grommet
Base Plate (m) to the Pole (a) using 3pcs
M5x14 Bolts (f), and tighten using the Allen
Key (o), see Figure 7.
2. Attach So Pad (w2) to the Grommet Base
Plate (m), see Figure 8.
3. Position the Pole (a) on the mounting surface
and secure using the Support Plate (j), M10
Washer (k), Spring Washer (l) and M10 Bolt (i).
Fasten the M10 Bolt using provided Wrench
(p), see Figure 9.
j
i
k
l
a
m
f
Figure 7
Figure 9
w2 Figure 8

5
STEP 2
Install Swivel Arms (d) to the Pole (a). Fasten the bolt with supplied Allen Key (o). Attach the Wire
Clip (n1, n2) to the pole (a) and Swivel Arms (d).
STEP 3
FOR LAPTOP
Attach VESA plate (e) to laptop tray (t) using
bolts (u) and M4 nuts (v).t
u
v
FOR FLAT BACK MONITOR
Attach VESA plate (e) to the monitor using
thumb bolts (q).
q
on1
n2
d

6
STEP 3 (continued)
FOR CURVED BACK MONITOR
Attach VESA plate (e) to the monitor using bolts
(r) and spacers (s).
s
r
STEP 4
Slide the monitor onto the head of Swivel Arm (d) as shown in the diagram. Install the security Nut
(h). Make sure the security nut is installed before you rotate the monitor.
h

7
STEP 5
Adjust as Desired
Tighten the bolt with the supplied Allen Key (o) to fix the tilt angle. Use the supplied Allen Key (o) to
make the necessary adjustments
o
o

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303