Vivo STAND-V002LW User manual

White Dual Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002l
SKU: STAND-V002LW
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x2)
VESA Plate
B(x2)
VESA Bracket
C(x1)
Base
M-A (x8)
M4x12
M-D (x8)
M5x16
J (x3)
Bolt
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
M-F (x8)
Spacer
M-E (x8)
D5 Washer
D(x1)
Pole
E(x1)
Pole
F (x1)
Pole Cap
G(x1)
Pole Connector
H (x2)
Cable Clip
I (x2)
Fastener
M-C (x8)
M5x12
M-B (x8)
M4x16
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
K (x1)
3mm Allen
Wrench
L (x1)
4mm Allen
Wrench
M (x1)
6mm Allen
Wrench

3
ASSEMBLY STEPS
STEP 1
Insert pole cap (F).
TOOLS NEEDED
Phillips
Screwdriver
STEP 2
Use allen wrench (L) on bolt (J) to secure the bottom pole (D) to the base (C).
22 lbs
Per Arm
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
F
E
D
C
J
L

4
STEP 3
Slide the cable management clip (H) down the pole followed by a single clamp (B). Choose your
desired height and secure the clamp to the pole with allen wrench (M).
STEP 4
Screw the pole connector (G) to the threads on top of pole (D) then add pole (E). Use allen wrench (K)
to tighten down the two screws inside the pole connector.
B
H
DM
K
D
G

5
STEP 5
OPTION A: Flat Back Monitor
Secure VESA plate (A) to the back of your monitor. Layer VESA plate on top of washer (M-E), then insert
correct size bolt to fit the holes in your monitor.
STEP 6
Add the second cable management clip (H) and single clamp (B) to desired height and secure to the
pole with allen wrench (M).
M
B
H
M- A
M- C
M- E
A

6
STEP 6 (Continued)
STEP 7
Slide the monitors onto (B) clamps. Use fasteners (I) to secure them.
OPTION B: Curved Back Monitor
Secure VESA plate (A) to the back of your monitor. Layer spacers (M-F), VESA plate, washers (M-E),
then insert correct size bolt to fit the holes in your monitor.
A
M- B
M- D
M- E
M- F
I

7
STEP 8
Adjust tilt angle with allen wrench (M).
STEP 9
Route wires through the cable management clips. Place allen wrenches into the cable management
clips for easy accessibility.
M
L
M
K

LAST UPDATED: 05/25/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303