Vivo STAND-V003FG User manual

Triple Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v003fg
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V003FG

2
PACKAGE CONTENTS
a (x1)
Pole
b(x1)
Glass Base
c(x1)
Arm
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
d(x1)
Decorative
Cover
e(x3)
M6x10
f (x3)
Connecting
Bolt
g (x3)
M8 Washer
h (x2)
M8x10
i (x4)
Rubber Feet j(x1)
So Pad
k(x1)
Allen Key
l (x1)
Wrench
m (x12)
M4x12
n (x12)
M4x30
o(x12)
M4 Spacer
p(x2)
Spare Plastic
Cover
q (x2)
VESA Plate
(side)
r (x1)
VESA Plate
(center)
s (x2)
Security Nut
t (x3)
M4x6 Bolt
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
Weighted Base Installation
Attach Rubber Feet (i) to the underside of the Glass Base (b).
Attach So Pad (j) to the Pole (a). Use a screwdriver to poke
holes for screws through the pad. Install Pole to Glass Base
using M6x10 Bolts (e), Connecting Bolts (f) and M8 Washers (g),
and tighten with medium Allen Key (k) and screwdriver. Slide
Decorative Cover (d) over the Pole.
ASSEMBLY STEPS
STEP 1
Figure 4
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
TOOLS NEEDED
Phillips
Screwdriver
i
j
d
e
f
g

4
STEP 2
Install Arm (c) to the Pole (a). Secure using M8x10 Bolts (h) with a Phillips screwdriver.
r
c
a
h

5
STEP 3
OPTION A: Flat Back Monitor
Fasten the VESA Plates (q, r) to monitors using M4x12 Thumbscrews (m). Do not overtighten;
Thumbscrews only need to be finger-tight.
OPTION B: Curved Back Monitor
Fasten the VESA Plates (q, r) to monitors using M4x30 Screws (n) and spacers (o).
r
m
r
n
o

6
STEP 4
Slide the center monitor onto the center head of Monitor Arm (c). Install the M4x6 bolt (t) to secure the
monitor. Slide the side monitors onto the heads of Monitor Arm (c). Install the Security Nuts (s).
t
c
c
c
c
s

7
STEP 5
Adjust the tilt and swivel. Remove the plastic cover and use the Allen Key (k) to adjust swivel joint
tension. Remove the plastic cover then use the wrench (l) to tighten the side tilt joints if the monitors
are not fully supported. Tighten the grub screw on back of center monitor joint if the monitor is not
fully supported.
STEP 6
STEP 7
Turn the bolt on the center of the monitor arm counter-clockwise to lower the center monitor or clock-
wise to raise the center monitor. Remove the security nut (s) and turn the bolt underneath with the
Allen Key (k) to raise or lower the side monitor. Replace the nut aer adjustment.
Manage cables for side monitors using the Cable Clips. Cables can also be hidden inside the pole.
Pry off the
Plastic Cap
k
l
k
grub screw

Last Updated: 09/06/2019
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654