Vivo STAND-V001Q User manual

Pneumatic Arm Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001q
SKU: STAND-V001Q
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
A (x1)
Arm
B(x1)
VESA Plate
C(x1)
Clamp Base
Support
H (x1)
Knob
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Clamp
E(x1)
Cable Clip
S-A (x1)
M8x105mm
Screw
S-B (x5)
M6x10mm
Screw
F (x1)
Base Support
G (x1)
Support Plate
I (x2)
Pad
M-A (x4)
M4x12
M-B (x4)
M5x12
M-C (x4)
M5 Washer
T-A (1)
4mm Allen
Wrench
T-B (x1)
6mm Allen
Wrench
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED 2-20lbs
(1-9kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
OPTION A: Clamp Installation
Install Clamp Base Support (C) onto base of Monitor
Stand (A) with M6x10mm Screws (S-B) using 4mm
Allen Wrench (T-A). Apply Pads (I) to bottom of Clamp
Base Support (C).
Secure Clamp (D) to upper two holes of Clamp Base
Support (C) with M6x10mm Screws (S-B) using 4mm
Allen Wrench (T-B) for desks with a thickness of
10-55mm. (Use lower two holes with for desks with a
thickness of 50-85mm)
Attach Cable Clip (E) to Clamp Base Support (C).
Tighten the clamp to the desktop using hand bolt.
A
C
10-55mm
D
50-85mm
E
T-A
I
S-B
S-B
T-A
T-A

4
STEP 1 (Continued)
OPTION B: Grommet Base Installation
Slide M8x105mm (S-A) through the top of the Base Support (F) and install on base of Monitor Stand
(A) with M6x10mm Screws (S-B) using 4mm Allen Wrench (T-A). Apply Pads (I) to bottom of Base
Support (F). Position stand on desk with M8x105mm Screw (S-A) through hole, and secure by using
the Support Plate (G) and Knob (G) on underside of the mounting surface.
F
S-B
S-A
H
G
H

5
STEP 2
Position VESA Plate (B) on back of monitor and secure with Screws (M-A or M-B) with M5
Washers (M-C).
STEP 3
Pull back latch on monitor arm, and slide monitor
into place.
STEP 4
If needed, adjust the bolt on the side of the hinge
behind the VESA plate to tighten or loosen the tilt
angle support. Adjust gas spring tension by turning
screw with 6mm Allen Wrench (T-B) . Clockwise
reduces tension, counter-clockwise increases
tension. The tension should be just enough to
hold your monitor in place without liing itself up.
NOTE:Tighten the socket set screw on the top of the
gas spring adjustment screw if the joints are making
a popping sound.
M- A
M- B
M- C
B
2
1
2
WARNING:
Monitor must be installed on mount
before making tension adjustments
to the gas spring arm.
Keep monitor in a straight
orientation when making
adjustments.
T-B
T-B

6
STEP 5
Remove cable covers as shown from upper and lower arms.
1
2
1

7
STEP 6
Replace covers making sure the cables have enough slack to allow free movement of the arm.
STEP 7
Store tools in Cable Clip (E) if clamp option is used.
1
2
1
180°
180°
+90°
-90°
270°
360°
L
M

LAST UPDATED: 02/01/2023
REV1.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303