Vivo STAND-V002Z User manual

Dual Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002z
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V002Z

2 3
ASSEMBLY STEPS
PACKAGE CONTENTS
TOOLS NEEDED
Phillips
Screwdriver
A (x1)
Pole
B(x1)
Weighted Base
C(x1)
Monitor Arm
NOTE: SOME HARDWARE MAY NOT BE USED
E(x3)
M5x14
F (x1)
M10 Bolt
G (x1)
Support Plate
H (x1)
M10 Washer
K (x2)
Wire Clip
L (x1)
Allen Wrench
OPTION A: Weighted Base Installation
Install the pole (A) to the weighted base (B) using M5x14 screws (E), and tighten using allen wrench (L).
Optionally, you can drill a 10mm diameter hole in your desk and secure using support plate (G), M10
washer (H), spring washer (I) and M10 bolt (F). Fasten the M10 bolt with provided wrench (M).
I(x1)
Spring Washer
J(x1)
Grommet Base
Plate
P (x8)
M4 Spacer
Q (x16)
M4 Washer
R (x4)
Cable Ring
N (x8)
M4x12
O(x8)
M4x30
STEP 1
M (x1)
Wrench
OPTION B: Grommet Base Installation
Install the grommet base plate (J) to pole (A) using M5x14 bolts (E), and tighten using allen wrench (L).
Secure to desk using the support plate (G), M10 washer (H), spring washer (I) and M10 bolt (F). Fasten
the M10 bolt using provided wrench (M).
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

4 5
STEP 1 (Continued)
OPTION C: Self-Drilled Grommet Base Installation
Install the grommet base plate (J) to pole (A) using M5x14 bolts (E), and tighten using allen wrench
(L). Secure to desk using the support plate (G), M10 washer (H), spring washer (I) and M10 bolt (F).
Fasten the M10 bolt using provided wrench (M).
STEP 3
STEP 2
Install monitor arm (C) to pole (A). Fasten with supplied allen wrench (L).
OPTION A: Flat Back Monitor
For monitors with flat backs attach VESA plate using M4x12 thumbscrews (N) and M4 washers (Q).
OPTION B: Curved Back Monitor
For monitors with curved back attach VESA plate using M4x30 screws (O), M4 washers (Q), and M4
spacers (P) as shown in diagram.

6 7
STEP 4 STEP 5
Attach wire clips (K) and cable rings (R) and manage wires as shown in diagram.Adjust monitor height by loosening the center bolt with the large Allen Wrench (L), then re-tighten
at desired height. Adjust monitor support joints using the knob on top of each bracket. If additional
tightening is needed, remove the monitor, tighten the center nut on the VESA plate with a 13mm
wrench (Not Included), and reinstall the monitor.

Last Updated: 12/13/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654