Vivo STAND-SIT2DD User manual

Sit to Stand Dual Monitor Desk Mount Workstation
with USB
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-sit2dd
SKU: STAND-SIT2DD
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Base
B(x1)
Adjustable Arm
C(x1)
Smartphone Tray
O (x1)
4mm Allen
Wrench
P(x1)
6mm Allen
Wrench
N(x1)
3mm Allen
Wrench
J (x1)
Clamp Plate
K (x1)
Clamp
L (x2)
VESA Plate
M (x1)
Cable Clip
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x1)
Keyboard Tray
E(x1)
Lower Support
Arm
F (x1)
Arm
G(x1)
Upper
Support Arm
H (x1)
Rear Cover
I (x1)
Clamp Brace
R(x2)
Carriage Bolt
Q(x1)
Grommet Base
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-A (x8)
M4x12
M-C (x8)
D5 Washer
M-B (x8)
M5x12
T (x2)
M8x25
S(x2)
Support
Plate
U(x6)
ST4.8x16
W(x2)
M5x10
V(x4)
M6x12
Y (x2)
Spring Washer
X(x2)
Nut
Z (x1)
Wrench

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
OPTION A: Clamp Installation
Attach clamp brace (I) to base (A) using M6x12 bolts (V), and tighten with 4mm Allen wrench (O).
Place clamp plate (J) on top of clamp (K). Install clamp (J) to upper holes of clamp brace (I) for a desk
thickness of 3/8” to 1-1/2” (10 - 40mm), or to lower holes for a desk thickness of 1-1/2” to 3-1/4” (40 -
84mm), and tighten with Allen wrench (P). Place assembled base on edge of desk and tighten clamp
bolts evenly with 6mm Allen wrench (P).
OPTION B: Grommet Installation
Place carriage bolts (R) into square holes in grommet base plate (Q). Attach grommet base plate to
base (A) using M6x12 bolts (V), and tighten with 4mm Allen wrench (O). Place assembled base over
cable grommet hole in desktop, and tighten using support plates (S), lock washers (Y) and M8 nuts (X),
and tighten with crescent wrench (Z). If a grommet hole isn’t present, drill a 3/8” (10mm) hole through
the desktop for each bolt.
K
J
IV
O
A
10-40m m
40-84m m
P
R
Q
O
V
SYZ
X
0 - 13.2 lbs
(0 - 6 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
2.2 lbs
(1 kg)
KEYBOARD

4
STEP 2
Carefully extend the adjustable arm (B) to the
raised position as shown. Insert the adjustable
arm into the socket of the base, then secure
using the 3mm Allen wrench (N).
N
B
STEP 3
Remove the knob from the lower support arm (E) to separate into lower support arm (E1) and knob
(E2).
E
E2
E1
STEP 4
Assemble smartphone tray (C) to lower support arm
using M5x10 screws (W) with a Phillips screwdriver.
C
W
E1
STEP 5
Assemble keyboard tray (D) to lower support arm
using ST4.8x16 screws (U) with a Phillips screwdriver.

5
STEP 6
Mount upper support arm (G) to lower support arm
using M8x25 bolts (T) and tighten with 6mm Allen
wrench (P).
Adjust keyboard tray tilt using the 4mm Allen wrench (O). Turn the adjustment screw clockwise to tilt
up to position 1a, and counter-clockwise to tilt down to position 1b. Install the knob (E2) to lock the
position.
STEP 8
STEP 7
Place the support arm/tray assembly onto the
upper post of the adjustable arm, then secure using
the wrench (N).

6
STEP 9
STEP 10
Install the VESA plate (L) to monitor using M4x12 bolts (M-A) or M5x12 bolts (M-B) with washers (M-C),
making sure the rounded edges of the rear bracket are facing up.
STEP 11
Place the monitors with VESA plates into the supports on the arm, then turn the screw on each support
to secure the monitors. Tighten with a Phillips screwdriver.
Remove the knob from arm (F). Slide the arm onto the upper support arm, then reinstall the knob.
Tighten the bolts with the 4mm Allen wrench (O) to secure height.
F
O

7
Adjust as Desired
STEP 12
STEP 13
Organize cables and reinstall cable covers to
base and adjustable arm.
STEP 14
Install rear cover (H) to clamp brace if the clamp
option was used. Install cable clip (M) to back
of upper support arm and remove cable covers
from base and adjustable arm.
Loosen knob in back to adjust monitor
height. To adjust gas spring support,
turn the hex screw on top of the rear joint
using the 6mm Allen wrench (P). Counter-
clockwise will increase support, and
clockwise will decrease support.
O
P

LAST UPDATED: 05/13/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303