Vivo STAND-V001M User manual

Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001m
SKU: STAND-V001M
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Arm
B(x1)
Clamp
C(x1)
Pole Cover
J (x1)
5mm Allen
Wrench
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Pole
E(x1)
Cable Clip
F (x1)
Grommet
Plate
G(x5)
Rubber Pad
H (x1)
Bolt
I (x1)
Support Plate
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
K (x1)
6mm Allen
Wrench
M-A (x4)
M4x12
M-B (x4)
M5x12
M-C (x4)
D5 Washer

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
22lbs
(10kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
Attach plastic cap (C) to the top of pole (D).
D C
STEP 2
OPTION A: Clamp Installation
Stick rubber pads (G) to the underside of clamp (B). Attach pole (D) to clamp (B) using bolt (H). Tighten
using 6mm allen wrench (K). Attach clamp (B) to desktop.
10-88 mm
K
H
G
B

4
STEP 2 (Continued)
STEP 3
Slide cable management clip (E) and arm (A) onto pole (D) and tighten using 5mm allen wrench (J).
I
10-75mm
B
G
F
OPTION B: Grommet Base Installation
For grommet hole mounting, remove screw in top of bolt on clamp (B). Stick rubber pads (G) to bottom
of grommet base (F). Attach metal plate (I) to bolt and run through grommet hole into grommet base
(F) and thread into pole (D) as shown in diagram.

5
STEP 4
Attach two bolts (M-A or M-B) and washers (M-C) to top mounting holes of monitor,
making sure to leave 3mm of threads exposed. Align bolts (M-A, M-B) in VESA plate.
Secure using two more bolts (M-A or M-B) and washers (M-C) in the bottom two holes.
Tighten all four bolts using phillips screwdriver.

6
STEP 5
Adjust tension in monitor bracket with 6mm allen wrench (K) as shown in diagram.

7
STEP 6
Store allen wrenches (K,J) in cable management clip (E) for future adjustment.
Adjust as Desired
J
K

LAST UPDATED: 08/26/2020
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303