Vivo STAND-V101L User manual

Pneumatic Arm Single Laptop Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101l
SKU: STAND-V101L
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Arm
B(x1)
Clamp
C(x1)
Clamp Cover
J (x1)
Grommet Base
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
VESA Plate
E(x1)
Pole
F (x1)
Cable Clip
G(x1)
Thumbscrew
H (x3)
Bolt
I (x1)
Support Plate
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
K (x1)
4mm Allen
Wrench
L (x1)
6mm Allen
Wrench
M-A (x4)
M4x12
M-B (x4)
M4x16
M-C (x4)
M5x12
M-D (x4)
M5x16
M-E (x4)
D5 Washer
M-F (x4)
Spacer
O (x2)
Cover
M (x1)
Bolt
N (x2)
Arm
P (x4)
Bolt

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
9.9lbs
(4.5kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
OPTION A: Clamp Installation
Adjust clamp (B) height according to thickness of desktop. Attach clamp cover (C) to clamp (B).
Secure pole (E) to clamp (B) using three bolts (H). Tighten using 4mm Allen wrench (K).
OPTION B: Grommet Base Installation
For grommet hole attachment, disassemble clamp (B) using 6mm Allen wrench (L) and a Phillips
screwdriver. Attach base (J) and pole (E) to 3/8” (10mm) grommet hole in desktop using bolt from
clamp (B) with plate (I).
2.2-17.6lbs
(1-8kg)
LAPTOP MONITOR

4
STEP 2
Slide cable management clip (F) over top of pole (E). Slide monitor arm (A) over pole and tighten bolt
using 6mm Allen wrench (L).
OPTION A: Flat Back Monitor
Attach VESA plate (D) to the back of
the monitor using bolts (M-A, M-C) and
washers (M-E).
OPTION A: MONITOR STEP 3
OPTION B: Curved Back Monitor
Attach VESA plate (D) to the back of the monitor
using bolts (M-B, M-D), washers (M-E), and
spacers (M-F).
Slide VESA plate (D) with
monitor over bracket on arm
(A). Secure using the thumb
screw (G). Remove the
bottom cover from arm (A).
OPTION A: MONITOR STEP 4

5
OPTION A: MONITOR STEP 5
Organize cables and re-attach cover.
OPTION A: MONITOR STEP 6
Adjust gas spring support in arm using 6mm Allen
wrench (L). Turning counter-clockwise increases
support, and clockwise decreases. Adjust tilt support
using 6mm Allen wrench (L).
OPTION A: MONITOR STEP 7
Adjust monitor position as desired.

6
Place laptop arms (N) underneath each side
of laptop tray (M), aligning square holes in
arms with the edge and long slot on each
side. Insert clips (O) through top to secure
arms, making sure all 4 locks on each clip are
engaged with square holes in arms.
OPTION B: LAPTOP STEP 3
Attach assembled laptop holder to
75mm and 100mm holes on arm
(A) using M4x8 screws (P). Tighten
screws using a Phillips screwdriver.
OPTION B: LAPTOP STEP 4
Slide VESA plate (D) with laptop tray (M) over bracket
on arm (A). Secure using the thumb screw (G).
OPTION B: LAPTOP STEP 5
Release locks on the underside of laptop arms (N). Extend arms, place laptop in holder, then adjust
arms to fit the width of the laptop. Engage locks to secure laptop. If using a thicker laptop, turn front
bumpers to the upward position for additional support.
OPTION B: LAPTOP STEP 6

7
Remove the bottom cover from arm (A).
OPTION B: LAPTOP STEP 7
Organize cables and re-attach cover.
OPTION B: LAPTOP STEP 8
Adjust gas spring support in arm using 6mm Allen wrench (L). Turning
counter-clockwise increases support, and clockwise decreases.
Adjust tilt support using 6mm Allen wrench (L).
OPTION B: LAPTOP STEP 9
Adjust laptop position as desired.
OPTION B: LAPTOP STEP 10

LAST UPDATED: 12/04/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303