Vivo STAND-V003M User manual

Triple Monitor Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v003m
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V003M

2 3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Stick so pads (I) to bottom of clamp base (D). Slide cable management clip (G) and base cover (H)
on to bottom of pole (B). Thread pole (B) onto clamp (D). Tighten grub screws in bottom of clamp (D)
using 3mm allen wrench (K). Secure clamp (D) to desktop as shown in diagram.
TOOLS NEEDED
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
OPTION B: Grommet Base Installation
Remove screw from top of bolt in clamp (D). Stick so pads (I) to bottom of grommet base (E). Slide
cable management clip (G) and base cover (H) on to bottom pole (B). Thread bottom pole (B) onto
grommet base (E). Tighten grub screws in bottom of grommet base (E) using 3mm allen wrench
(K). Slide metal pad (J) over bolt and slide through grommet hole in bottom of desktop. Thread into
bottom of pole (B).
PACKAGE CONTENTS
A (x1)
Arm
B(x1)
Pole
C(x1)
VESA Bracket
M-A (x12)
M4x12
M (x1)
6mm Allen
Wrench
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x1)
C-Clamp
E(x1)
Grommet Plate
F (x6)
Cable Clip
G(x1)
Cable Clip
H (x1)
Base Cover
L (x1)
5mm Allen
Wrench
M-C (x12)
D5 Washer
M-B (x12)
M5x12
J (x1)
Support Plate
I (x5)
So Pad
K (x1)
3mm Allen
Wrench
I
10-88mm
K
G
H
D
B
DE
I
10-8 0 mm
G
H
J
K
B
17.6 lbs
Per Arm
(7.98 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

4 5
STEP 2
Slide arm (A) and bracket (C) over top of pole and tighten using 5mm allen wrench (L).
STEP 3
Attach cable management clips (F) as shown in diagram.
STEP 4
Attach two bolts (M-A or M-B) and washers (M-C) to top mounting holes of monitor, making sure
to leave 3mm of threads exposed. Align bolts (M-A or M-B) in VESA plate. Secure using two more
bolts (M-A or M-B) and washers (M-C) in the bottom two holes. Tighten all four bolts using phillips
screwdriver.
C
A
L
23mm
L
F
M- A
M- B
M- C
12
3m m
3
M- A
M- B
M- C

6 7
STEP 5 STEP 7
STEP 6
Store allen wrenches (M, L) in cable management clip (G) for future adjustment.
Adjust tension in monitor bracket with 6mm allen wrench (M) as shown in diagram. Adjust height of monitors using 5mm allen wrench (L) as shown in diagram.
+45°
-45°
M
L
M
L

Last Updated: 11/06/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654