Vivo STAND-GM2BB User manual

Dual Gaming Pneumatic Monitor - Blue LED Lights
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-gm2bb
SKU: STAND-GM2BB
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2 3
ASSEMBLY STEPS
OPTION A: Clamp Installation
Loosen the hand bolts on the clamp (C) to fit the desk thickness. Place the clamp on
the desk edge and tighten, then press the base cover (B) over the top of the clamp.
PACKAGE CONTENTS
TOOLS NEEDED
0 - 17.6lbs
(0-8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x2)
Arm
B(x1)
Base Cover
C(x1)
Clamp
M-A (x8)
M4x12
M-B (x8)
M4x30
M-C (x8)
Spacer
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
D(x2)
VESA Plate
E(x1)
LED Power
Cable
F (x2)
M4x10 Bolt
G(x1)
3mm Allen
Wrench
I (x1)
5mm Allen
Wrench
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE MAY NOT BE USED
PER SCREEN
Do not overtighten screw!
STEP 1
STEP 2
Place the arms (A) on top of the base (C).
J(x1)
Carriage Bolt
K (x1)
Wingnut
L (x1)
Support Plate
S=3mm
Desk
OPTION B: Grommet Installation
Remove the clamps from the base (C) using the 4mm Allen wrench (H). Drop the carriage
bolt (J) down through the square hole in the base and position over the desk grommet
hole (if needed, drill a 3/8” [10mm] hole through desk), and secure using the support
plate (L) and wingnut (K). Press the base cover (B) over the top of the base.
S=4mm
Loosen
Desk
Desk
H(x1)
4mm Allen
Wrench

4 5
STEP 3
OPTION A: Flat Back Monitors
Attach the VESA plates (D) to the monitors using M4x12 bolts (M-A), making sure the
opening on each is facing towards the bottom of the monitor, and tighten with a Phillips
screwdriver.
OPTION B: Curved or Recessed Back Monitors
Attach the VESA plates (D) to the monitors using M4x30 bolts (M-B) and spacers (M-C),
making sure the opening on each is facing towards the bottom of the monitor, and tighten
with a Phillips screwdriver.
STEP 5
Slide the monitors with VESA plates (D) onto the heads of the arms (A), and secure using
M4x10 bolts (F) with a Phillips screwdriver. If needed, adjust the gas spring in each arm
to support the monitors using the 5mm Allen wrench (I). While holding the arm in the
straight forward position, turn the screw in back clockwise to decrease support, and
counter-clockwise to increase.
FLAT SCREEN MONITORS CURVED SCREEN MONITORS
STEP 4
Desk
STEP 6
Adjust the tilt support by turning the bolt immediately behind each tilt joint, and the
swivel by turning the bolt on the back of the bracket.
Slide the monitors with VESA plates (D) onto the heads of the arms (A), and secure using
M4x10 bolts (F) with a Phillips screwdriver.
S=5mm
S=5mm
Swivel
Tilt
Desk

6 7
Plug the LED power cable (E) into the connectors on the back of the arms (A) and base
cover (B), then connect to a USB port on the computer to power on.
STEP 8
STEP 7
Remove the cable covers from the arms (A) by sliding each one forward and o (loosen
screws for upper covers if needed). Run cables through the upper covers and lower arms,
then reinstall the covers.
Desk
C
8
Desk

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303