Vivo STAND-V006F User manual

  
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-  
 
phillips screwdriver
 
1
Scan the QR code with your mobile device or follow the link
to helpful videos and specifications related to this product.
 


 
! 
  
" 
 

# 
 

 
 
$  
!"
  
! 
% 
  #
& $
!%
' 
&# #
( 
' 
 
( 
) 
 )*
  
 
 
$(

 
 
 (
! 
( 
* 

+ 
 
 
!
, 

- --.//00 12/./ 03
 
+# 
" 
 

245 .
2
. !  -  5
).  ,- 
).  $22 %
).  $22 % 6-
,- 
Attach pole (A) to weighted
base (B) using screws (J). Slide
decorative cover (K) onto pole
(A).
Slide washer (N1) onto grommet bolt (M).
Slide spring washer (N2) onto grommet
bolt (M). Slide grommet plate (L) onto
grommet bolt (M). Insert grommet bolt
(M) through desk from bottom. Hand
screw pole (A) onto grommet bolt (M).
Tighten with wrench (W). Slide decorative
cover (K) onto pole (A).
Attach pole (A) to weighted base (B)
using screws (J). Slide washer (N1) onto
grommet bolt (M). Slide spring washer
(N2) onto grommet bolt (M). Slide
grommet plate (L) onto grommet bolt
(M). Insert grommet bolt (M) through
desk and weighted base (B) from
bottom. Tighten with wrench (W). Slide
decorative cover (K) onto pole (A).
. " 24 - 2   %  -

Attach the curved arms (D) using arm clamps (F). Attach with arm
connects (E), bolts (G), and washers (H) as shown in diagram. Slide
arm sets onto pole (A) and secure with bolts (T) using allen wrench
(O). Attach wire clips (U).

. 7 - -   2   8
-  
Fasten the grub screw
on each VESA plate
with small Allen
Wrench (O) to adjust
tilt angle.
Attach center monitors with VESA plates (C2) to arm connect
brackets (E) using M4x16 bolts with washers (V). Attach side
monitors with VESA plates (C1) by sliding onto arms and tightening
knobs. Press arm covers (I) onto ends of arms
. 9  -   # 
).    
).  0  
Mount monitors to
the VESA plates (C1,
C2). For flat back
monitors secure
with screws (Q) and
washers (P).
For curved back monitors secure with screws (R), washers
(P), and spacers (S).
3

If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by incorrect
assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
35 ,
  
Last updated: 0 /30/18
. : 8 -  (0   -
,
Fasten or loosen the bolt on the above diagram to adjust the level of
each monitor. Manage wires and adjust monitors as desired.
4