Vivo STAND V002Z User manual

Dual Monitor Stand
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
- Model: STAND V002Z
Tools Required:
phillips screwdriver
Package Contents
1
Scan the QR code with your mobile device or follow the link
to helpful videos and specifications related to this product.
A (x1)
Pole
B (x1)
Weighted Base
C (x1)
Monitor Arm
F (x1)
M10 Bolt
(x1)
Support Plate
H (x1)
M10 Washer
I (x1)
Spring Washer
J (x1)
Grommet Base
Plate
K (x2)
Wire Clip
L (x1)
Allen Wrench
M (x1)
Wrench
O (x8)
M x30
P (x8)
M Spacer
R (x )
Cable Ring
N (x8)
M x12
Q (x16)
M Washer
- -https://vivo us.com/products/stand v002z
E (x3)
M5x1

Step 1: Install Pole to the Desktop (Continued)
- Option C: Self Drilled rommet Base Install
Step 2: Install Monitor Arm to Pole
Install monitor arm (C) to pole (A). Fasten with supplied allen wrench
(L).
Drill a 8. mm hole or larger through the
mounting surface. Install the grommet base
plate (J) to pole (A) using M x14 bolts (E), and
tighten using allen wrench (L).
Secure to desk using the support plate (G),
M10 washer (H), spring washer (I) and M10
bolt (F). Fasten the M10 bolt using provided
wrench (M).
Assembly Steps
2
Step 1: Install Pole to the Desktop
Option A: Weighted Base Install
Option B: Existing rommet Base Install
Install the pole (A) to the weighted
base (B) using M x14 screws (E),
and tighten using allen wrench (L).
Optionally, you can drill a 10mm
diameter hole in your desk and
secure using support plate (G),
M10 washer (H), spring washer (I)
and M10 bolt (F). Fasten the M10
bolt with provided wrench (M).
Install the grommet base plate (J) to
pole (A) using M x14 bolts (E), and
tighten using allen wrench (L).
Secure to desk using the support
plate (G), M10 washer (H), spring
washer (I) and M10 bolt (F). Fasten the
M10 bolt using provided wrench (M).

Step 4: Adjusting the Mount
Adjust monitor height by loosening the center bolt with the large
Allen Wrench (L), then re-tighten at desired height. Adjust monitor
support joints using the knob on top of each bracket. If additional
tightening is needed, remove the monitor, tighten the center nut on
the VESA plate with a 13mm wrench (Not Included), and reinstall the
monitor.
Step 3: Mount the Monitor to VESA Plate
Option A: Flat Back Monitor
Option B: Curved Back Monitor
For monitors with flat backs attach VESA plate using M4x12
thumbscrews (N) and M4 washers (Q).
For monitors with curved back attach VESA plate using M4x30 screws
(O), M4 washers (Q), and M4 spacers (P) as shown in diagram.
3

If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by incorrect
assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
Safety Warning
Contact us at:
Last updated: 0 /29/18
Step 5: Install the Wire Clips & Manage the Wires
Attach wire clips (K) and cable rings (R) and manage wires as shown in
diagram.
4