Vivo STAND-V012F User manual

Dual Monitor Extra Tall Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v012f
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V012F

2
PACKAGE CONTENTS
WARNING!
a (x1)
Pole
b(x1)
Weighted Base
c(x1)
Swivel Arm
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
d(x2)
VESA Plate
e(x3)
M5x14
f (x2)
Nut
g (x1)
M10 Bolt
h (x1)
Support Plate
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
i(x1)
M10 Washer
j(x1)
Spring Washer
k (x1)
Grommet
Base Plate
l1 (x3)
Wire Clip
l2 (x4)
Wire Clip
m(x1)
Allen key
n (x1)
Wrench
o (x8)
M4x12
p (x8)
M4x30
q (x8)
M4 Spacer
r(x1)
So Pad

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
OPTION A: Clamp Installation
Install the Pole (a) to the Weighted base (b) using 3 M5x14 Bolts (e) and tighten using the Allen Key (m),
see Figure 1. Optionally, you can drill a 10mm diameter hole in your desk and secure using the Support
Plate (h), M10 Washer (i), Spring Washer (j) and M10 Bolt (g). Fasten the M10 Bolt with provided
Wrench (n), See figure 2.
STEP 2
Remove the grub screws from poles (a) using the small Allen Key (m). Connect the poles by threads.
Install grub screws and fasten them by provided Allen Key (m).
a
e
b
h
g
i
l
j
Figure 2
Figure 1
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
Drill

4
STEP 2 (Continued)
OPTION B: Grommet Base Installation
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before
installing the desk mount. Install the Grommet Base Plate (k) to the Pole (a) using 3pcs M5x14 Bolts
(e), and tighten using the Allen Key (m), see Figure 3. Attach So Pad (r) to the Grommet Base Plate
(k), see Figure 4. Position the Pole (a) on the mounting surface and secure using the Support Plate (h),
M10 Washer (i), Spring Washer (j) and M10 Bolt (g). Fasten the M10 Bolt using provided Wrench (n),
see Figure 5.
OPTION C: Self-Drilled Grommet Base Installation
Position the Pole (a) on the mounting surface and mark the center hole. Drill a 3/8” (10mm) diameter
hole at the marked position through the mounting surface. Install the Grommet Base Plate (k) to the
Pole (a) using 3pcs M5x14 Bolts (e), and tighten using the Allen Key (m), see Figure 6. Attach So Pad
(r) to the Grommet Base Plate (k), see Figure 7. Position the Pole (a) on the mounting surface and
secure using the Support Plate (h), M10 Washer (i), Spring Washer (j) and M10 Bolt (g). Fasten the M10
Bolt using provided Wrench (n), see Figure 8.
h
g
i
j
a
k
e
Figure 3
Figure 5
rFigure 4
h
g
i
j
k
a
e
Figure 6
Figure 8
rFigure 7

5
STEP 3
Install Swivel Arm (c) to the Pole (a). Fasten the bolt with supplied Allen Key (m). Attach the Wire Clip
(l1,l2) to the Pole (a) and Swivel Arm (c).
STEP 4
OPTION A: Flat Back Monitor
Attach VESA Plate (d) to back of monitor using
bolts (o).
OPTION B: Curved Back Monitor
Attach VESA Plate (d) to back of monitor using
bolts (p) and spacers (q).
STEP 5
Slide the monitor onto the head of Swivel Arm (c). Install the security Nut (f). Make sure the security
nut is installed before you rotate the monitor.
c
m
l1
l2
oq
p
f

6
STEP 6
Tighten the bolt with the supplied Allen Key (m) to fix the tilt angle. If one monitor is lower, remove
the Nut (f) and turn the bolt counter-clockwise with the Allen Key (m) to raise the monitor. Replace
Nut (f) aer the adjustment.
m
Fix the tilt angle
m
Ignore this step if
monitors are level

7
STEP 7
Use the supplied Allen Key (m) to make any necessary adjustments.
Manage the wires and store the Allen keys (m) in the Wire Clip (l1) for future use.
m
l1

Last Updated: 08/30/2019
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654