Vivo STAND-V003FG User manual

Triple Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v003fg
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V003FG

2 3
ASSEMBLY STEPS
PACKAGE CONTENTS
a (x1)
Pole
b(x1)
Weighted Base
c(x1)
Arm
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
d(x1)
Decorative
Cover
e(x3)
M6x10
f (x3)
Connecting
Bolt
g (x3)
M8 Washer
h (x2)
M8x10
k (x1)
M10 Washer
l (x1)
Spring Washer
i(x1)
M10 Bolt
j(x1)
Support Plate
STEP 1
m (x4)
Rubber Feet
n(x1)
So Pad
o(x1)
Allen Key
p (x1)
Wrench
q(x12)
M4x12
r (x12)
M4x30
s(x12)
M4 Spacer
t(x2)
Spare Plastic
Cover
u (x2)
VESA Plate
(side)
v (x1)
VESA Plate
(center)
w (x2)
Security Nut
x(x3)
Bolt
OPTION A: Weighted Base Installation
Attach Rubber Feet (m) to the Weighted Base (b). Attach So
Pad (n) to the Pole (a) and poke screw holes in pad using a
screwdriver. Install the Pole (a) to the Weighted Base (b) using
M6x10 Bolts (e), Connecting Bolts (f) and M8 Washers (g) and
tighten using the Allen Key (o), insert the Decorative Cover (d)
to the Pole (a).
OPTION B: Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before
installing the desk mount. Attach So Pad (n) to the Pole (a). Position the Pole (a) on the mounting
surface and secure using the Support Plate (j), M10 Washer (k), Spring Washer (l) and M10 Bolt (i).
Fasten the M10 Bolt using provided Wrench (p). Insert the Decorative Cover (d) to the Pole (a).
Figure 4
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
TOOLS NEEDED
Phillips
Screwdriver

4 5
STEP 1 (Continued)
OPTION C: Self Drilled Grommet Base Installation
Position the Pole (a) on the mounting surface and mark the center hole. Drill a 3/8” (10mm) diameter
hole at the marked position through the mounting surface. Attach So Pad (n) to the Pole (a). Position
the Pole (a) on the mounting surface and secure using the Support Plate (j), M10 Washer (k), Spring
Washer (l) and M10 Bolt (i). Fasten the M10 Bolt using provided Wrench (p). Insert the Decorative
Cover (d) to the Pole (a).
STEP 3
OPTION A: Flat Back Monitor
Fasten the VESA plates (u, v) to monitors using thumbscrews (q). Do not overtighten; thumbscrews
only need to be nger-tight.
OPTION B: Curved Back Monitor
Fasten the VESA plates (u, v) to monitors using M4x30 screws (r) and spacers (s).
STEP 2
Install Monitor Arm (c) to the pole, making sure the wire clips are facing down. Fasten the M8x10 bolt
(h) by screw driver.
r

6 7
STEP 4 STEP 5
Manage cables for side monitors using the cable clips. Cables can also be hidden inside the pole. To
adjust swivel joints, remove the plastic cover, then use the 6mm Allen key (o) to turn the bolt. Slide the
side monitors onto the heads of monitor arm (c). Install the security nut (w).Slide the center monitor
onto the head of monitor arm (c). Install the M4x6 bolt (x) to secure the monitor.
Adjust the tilt and swivel. Use the Allen Key (o) to adjust swivel joint tension. Use the wrench (p) to
tighten the side tilt joints if the monitors are not fully supported. Fasten the grub screw on back of
center monitor joint if the monitor is not fully supported.
STEP 6
STEP 7
Turn the bolt on the center of the monitor arm counter-clockwise to lower the center monitor or clock-
wise to raise the center monitor. Remove the security nut (w) and turn the bolt with the Allen Key (o) to
raise or lower the side monitor. Replace the nut aer adjustment.
Manage wires.
Pry off the
Plastic Cap

Last Updated: 11/29/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654