Vivo STAND-V002D User manual

Pneumatic Arm Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002d
[email protected]om www.vivo-us.com 309-278-5303
SKU: STAND-V002D

2
PACKAGE CONTENTS
A (x1)
Monitor Stand
B(x1)
Base Support
C(x1)
Clamp
J (x1)
4mm Allen
Wrench
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Base Cover
E(x1)
Bolt
F (x1)
Base Support
G (x1)
Clamp Knob
H (x5)
Bolt
I (x1)
Support Plate
K (x1)
5mm Allen
Wrench
M-A (x8)
M4x12
M-B (x8)
M5x12
M-C (x8)
D5 Washer
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
13.2 lbs
(6 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Install the clamp base support (B) onto the base of the monitor stand (A) with bolts (H) using provided
4mm Allen wrench (J). Secure clamp (C) to upper two holes with bolts (H) using 4mm Allen wrench (J)
for desk with a thickness of 10-55mm. Secure clamp (C) to upper two holes with bolts (H) using 4mm
Allen wrench (J) for desk with a thickness of 10-85mm. Attach cover (D) to base support. Tighten the
clamp to the desktop using the plastic knob.
A
B
J
H
10-55mm
J
H
C
50-85mm
D

4
STEP 1 (Continued)
OPTION B: Grommet Base Installation
Slide the long bolt (E) through the top of the grommet base support (F) and install on base of monitor
stand with bolts (H) using 4mm Allen wrench (J). Position stand on desk with long screw through hole,
and secure by using the support plate (I) and clamp knob (G) on underside of the mounting surface.
NOTE: For self-drilled installation, drill an 8.5mm hole or larger through the mounting surface.
STEP 2
Insert screws (M-A or M-B) with washers (M-C) into top two holes of monitor, leaving 3mm of thread
exposed. Hang monitor over slots in VESA plates. Secure monitor with screws and washers in bottom
two holes and tighten top screws.
E
F
H
J
G
I
M- A
M- B
M- C
M- A
M- B
M- C
3mm
K

5
STEP 3
Adjust gas spring tension by turning screw with 5mm Allen wrench (K). Clockwise reduces tension,
counter-clockwise increases tension. The tension should be just enough to hold your monitor in place
without liing itself up. If needed, adjust the bolt on the side of the hinge behind the VESA plate to
tighten or loosen the tilt angle support.
K

6
STEP 4
Remove cables covers as shown from upper and lower arms.
1
2

7
STEP 5
Adjust as Desired
Replace covers making sure the cables have enough slack to allow for free movement of the arms.
2
1
360°
360°
360°
180°
+90°
-90°

LAST UPDATED: 10/28/2019
Open Monday-Friday from 7:00am-7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times.
If any parts are received damaged or defective, please contact us.
We are happy to replace parts to ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]
www.vivo-us.com
309-278-5303
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
AVG. RESOLUTION TIME (within oice hrs): < 15 M