Vivo Easel Studio STAND-TV70C User manual

Easel Studio TV Stand with RGB Light
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv70c
SKU: STAND-TV70C,D
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Base with RGB
Light
B(x4)
Leg
C(x2)
Pole
D (x1)
Upper VESA
Bracket
E (x1)
Lower VESA
Bracket
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
I (x1)
Security
Cable
J (x2)
Security
Clip
K (x2)
Security Cable
Clamp
F (x6)
Cable Clip
T-B (x1)
2mm Allen
Wrench
T-A (x1)
4mm Allen
Wrench
W-A (x4)
ST4.8x38mm
Screw
W-B (x4)
Concrete Anchor
M-I (x2)
M5 Washer
G (x1)
Remote
H (x1)
Power Cord
M-A (x4)
M6x14mm
Screw
M-B (x4)
M8x16mm
Screw
M-C (x4)
M6x30mm
Screw
M-D (x4)
M8x35mm
Screw
M-E (x4)
M8 Washer
M-F (x4)
5mm Spacer
M-G (x4)
15mm Spacer
TOOLS NEEDED
Phillips
Screwdriver Drill Tape Measure Level Pencil
S-A* x6)
ST4.2x12
Screw
*ONLY USED ON STAND-TV70D

3
ASSEMBLY STEPS
STEP 1
Screw Legs (B) into the Base (A).
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting hardware for brick and concrete walls. If unsure, please contact us at
vivo-us.com, email at [email protected]om, or call us at 309-278-5303.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
88lbs
(40kg)
STEP 2
Screw Poles (C) onto the Base (A). Loosen the Support Rings (C1) on Poles (C) using
the 4mm Allen Wrench (T-A). Adjust RIngs to hold the TV at the desired height, using a
tape measure to ensure the rings are adjusted evenly, and tighten with the 4mm Allen
Wrench (T-A). NOTE: Rings should be at least 2” below the tops of the poles.
Be sure the support ring is
secured before installing the TV.
Screws should be facing to the
back.
C1
T-A

4
STEP 4
OPTION A: Flat Back TV
Position Upper VESA Bracket (D) over top holes on TV and secure with Screws (M-A or M-B),
M8 Washers (M-E), M5 Washers (M-I) and Security Clips (J). Position Lower VESA Bracket
(E) on the bottom holes and secure using Screws (M-A or M-B) and M8 Washers (M-E).
STEP 3
Remove Screws (E1) from the Lower VESA Bracket (E) using a Phillips screwdriver
and open the clamps.
OPTION B: Curved Back TV
Position Upper VESA Bracket (D) over top holes on TV and secure with Screws (M-C or M-D),
M8 Washers (M-E), and Security Clips (J). Position Lower VESA Bracket (E) on the bottom
holes and secure using Screws (M-A or M-B) and M8 Washers (M-E). Spacers (M-F, M-G) may
be required.
E1
M-I
JJ
JJ

5
STEP 5
Slide the TV onto assembled stand. Close the clamps on the Lower VESA Bracket (E) over
the poles and secure with the previously removed Screws (E1).
Peel backing from the Cable Clips (F) and install clips on the rear legs.
For STAND-TV70D: Secure clips by threading ST4.2x12mm Screws (S-A) directly into the
wood legs. Use clips to organize cables.
STEP 6
Plug Power Cable (H) into the RGB power connector in the back of Base (A), and connect
the USB end to a USB port on the TV, a phone charger or other device.
Flashing color sequence
Brightness +/-
Flash/Breathing Speed
OFF / ON
Flash white
Breathing color sequence
Smooth RGB sequence
Select color
Note: Remove the battery’s plastic insert
before using the remote.
Note: The LED Lighting is powered by any 5V DC power supply
including USB adapters that are included with most phones.
Ensure the RGB power
connector is facing to
the back of the stand.
STAND-TV70C STAND-TV70D
E1
F
S-A
H

6
STEP 6 (Continued)
To connect to an external RGB controller, remove the screw on the underside of the Base (A)
holding the le side cover, then remove the cover. Remove the security tape from the RGB
connector, then disconnect and pull out the cable. Connect the cable to the external RGB
controller. Pin1 is indicated by a dot on the connector.
STEP 7
OPTION A: Wood Stud Wall
Using Security Cable Clamps (K) as guides, mark drilling locations on wall at the same
height as the upper VESA bracket. Use of a stud finder is recommended. Drill holes
at least 1.6” (40mm) deep using a 1/8” (3mm) drill bit. Mount clamps to wall using
ST4.8x38mm Screws (W-A).
W-A

7
STEP 7 (Continued)
OPTION B: Concrete/Brick Wall
Using Security Cable Clamps (K) as guides, mark drilling locations on wall at the same
height as the upper VESA bracket, spaced 400mm - 650mm (16” - 26”) apart. Drill holes at
least 1.6” (40mm) deep using a 9/32” (7mm) drill bit. Insert Concrete Anchors (W-B) into
holes and mount Clamps (K) to wall using ST4.8x38mm Screws (W-A). Thread Security
Cable (I) through Security Clips (J) on TV and center holes in cable clamps as shown, then
tighten Clamps (K) using the 2mm Allen Wrench (T-B).
Thread Security Cable (I) through
Security Clips (J) on TV and center
holes in cable clamps as shown, then
tighten clamps using the 2mm Allen
wrench (T-B).
J
I
I
T-B
K
W-B
W-A
K
J
T-B
I
I

LAST UPDATED: 02/09/2023
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303