Vivo STAND-E-102B User manual

Black Electric Single Motor Desk Frame
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-e-102b
SKU: STAND-E-102B
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
1

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
WARNING!
PACKAGE CONTENTS
A (x1)
Telescopic
Crossbar
B x1)
Sync Rod
C(x1)
Cable Management
Tray
D(x2)
Foot
E(x2)
Side Bracket
F(x1)
AC Adapter
G (x2)
Hook
H x1)
Motorized Leg
I(x1)
Leg
J(x1)
Power Cable
K(x1)
Control
Panel
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
L(x3)
Cable Clip
M (x8)
Rubber Pad
N x3)
So Pad
S-B x10)
ST4.2x20mm
Screw
S-C (x2)
ST3.5x18mm
Screw
S-D (x4)
M4x6mm
Screw
S-A (x16)
M6x12mm
Screw
T-A x1)
4mm Allen
Wrench
O (x1)
Splitter Cable

3
110 lbs
(50kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Loosen the two set screws on the Telescopic Crossbar (A) using the 4mm Allen Wrench (T-A). Adjust
the crossbar length to suit the desktop. Re-tighten all screws. NOTE: Make sure adjusted length of the
Telescopic Crossbar is no more than 61" (155cm).
TOOLS NEEDED
Phillips
Screwdriver
STEP 2
Attach the Telescopic Crossbar to the Legs (H, I) as shown using M6x12mm Screws (S-A), and tighten
with the 4mm Allen Wrench (T-A).
Drill
NOTE: Insert all necessary screws into holes
before tightening.
T-A
T-A
T-A
T-A
T-A
T-A
A
T-A
T-A
T-A
I
H
S-A
Including monitors, the weight capacity is 154 lbs (70kg).

4
STEP 3
STEP 4
STEP 5
If you are using a VIVO desktop please follow the
manual that came with it. Otherwise, place frame
upside down on desktop and drill pilot holes for
screws. Use a 3/32” (3mm) bit, and drill holes to a
depth of 3/8” (10mm).
Place the Feet (D) on the legs as shown. Insert and tighten
M6x12mm Screws (S-A) using the 4mm Allen Wrench (T-A).
Attach the Side Brackets (E) to both ends of the frame using four M6x12mm Screws (S-A). Tighten with
the 4mm Allen Wrench (T-A).
T-A
T-A
T-A
T-A
T-A
E
S-A
S-A
D
Drill

5
STEP 6
STEP 7
Attach Hooks (G) to Cable Management Tray (C) using M4x6mm Screws
(S-D) with a Phillips Screwdriver. Hang the tray onto the telescopic
crossbar and tighten knobs to secure.
Position the frame upright. Loosen the knobs on the Sync Rod (B) and extend the hex sha. Insert hex
sha into the Leg (I), making sure the metal retaining ring makes contact with the leg. While holding the
hex sha with one hand, extend sync rod onto the spline sha of the motorized leg. Re-tighten knob.
CAUTION: To avoid injury, at least two people should
turn the frame upright.
OPTIONAL: Remove paper backing from So Pads (N)
and stick them to the inside and top of Hooks (G).
G
N
S-D
I
B
C
G
N
G
Knob
1
2
3

6
M
M
M
M
STEP 8
STEP 9
Connect Motorized Leg (H) to the Control Panel (K1). Connect Splitter Cable (O2) to Control Panel (K2).
Connect Splitter Cable (O1) to AC Adapter (F).Connect the Power Cable (J) to the AC Adapter (F).
Remove the protective film from the adhesive Rubber Pads (M). Position the rubber pads on the side
brackets and telescopic crossbar as shown.
FJ
K1K2
O1
O
F
K1
K2
DC plug
O2
O
K
O1
USB - Used in manual #2
Used in manual #2
H

7
STEP 11
STEP 12
Attach the control panel to the underside of the desktop using ST3.5x18mm Screws (S-C) as shown.
Once control panel is installed, Cable Clips (L) can be attached to the desk for cable management.
Refer to Control Panel User Guide for operational instructions.
If necessary, adjust foot pads to level desk.
Failure to follow these instructions may result in property damage and/or personal injury.
L
S-C
L
1
2
Drill
STEP 10
If you are using a VIVO desktop, Refer to the manual that came with your desktop.
If you are not using a VIVO desktop, place the desktop on the frame, and secure the desktop using the
ST4.2X20mm Screws (S-B). Make sure your desktop is greater than 1" (25mm) thick using screws (S-B).
S-B

LAST UPDATED: 1/19/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303