Vivo STAND-V101G1/W User manual

Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/stand-v101g1
SKU: STAND-V101G1/W
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
Pneumatic Arm Single Monitor Desk Mount
Instruction Manual

2
PACKAGE CONTENTS
TOOLS NEEDED
33lbs
(15kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Base
B (x1)
Lower Arm
C (x1)
Gas Spring Arm
J (x1)
Clamp
S-A (x4)
M6x12mm Screw
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot
be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate
use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
M-A (x4)
M4x12mm Screw
D (x1)
VESA Plate
E (x1)
Clamp Plate
F (x1)
Grommet Plate
G (x1)
So Pad
H (x1)
Cover
I (x1)
Clamp Brace
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-B (x4)
M5x12mm Screw
M-C (x4)
M5 Washer
T-B (x1)
4mm Allen Wrench
T-C (x1)
6mm Allen Wrench
T-A (x1)
3mm Allen Wrench

3
6mm
ASSEMBLY STEPS
STEP 1 (Option A)
Clamp Installation
Attach Clamp Brace (I) to Base (A) using M6x12mm Screws (S-A) and 4mm Allen Wrench (T-B). Apply
So Pad (G) to underside of Base (A).
Loosen screws on the back of Clamp (J), leaving 6mm of thread exposed. Assemble Clamp (J) to
Clamp Brace (I) in the correct position to fit the thickness of your desktop, and retighten screws
using 4mm Allen Wrench (T-B). Place Clamp Plate (E) on top of clamp bolts.
Position Base (A) on desktop and tighten clamp bolts evenly using 6mm Allen Wrench (T-C).
Attach Cover (H) to back of Clamp Brace (I).
T-B
S-A
I
AG
J
T-B
T-C HI
A
I
OR
EE

4
Grommet Base Installation
Attach Grommet Plate (F) to Base (A) using
M6x12mm Screws (S-A) and tighten with
4mm Allen Wrench (T-B). Apply So Pad
(G) to underside of Base (A). Position Base
(A) over grommet hole in desktop, or drill
a 3/8” (10mm) hole through the desk for
installation. Remove clamp bolt from Clamp
(J) using 6mm Allen Wrench (T-C). Insert
clamp bolt with Clamp Plate (E) up through
the underside of the desk and tighten to Base
(A) using the 6mm Allen Wrench (T-C).
STEP 2
STEP 3
Place Lower Arm (B) on top of Base (A), and secure by turning the lower screw in back with 3mm Allen
Wrench (T-A). Optionally, also tighten the upper screw to restrict swivel movement to +/-90 degrees.
Assemble Gas Spring Arm (C) to Lower Arm (B), and secure by tightening the set screw in Lower Arm
(B) using 3mm Allen Wrench (T-A).
S-A
T-B
T-C
E
J
G
F
A
A
B
C
B
T-A
STEP 1 (Option B)
T-AT-A
±1 0°
8

5
STEP 4
Install VESA Plate (D) to monitor using M4x12mm Screws (M-A) or M5x12mm Screws (M-B) with M5
Washers (M-C), making sure the arrow on VESA Plate (D) is pointing up.
STEP 5
Pull back the release lever on the support bracket, then place the monitor with VESA Plate (D) into
the support.
STEP 6
If needed, adjust gas spring arm to support the monitor using the 6mm Allen Wench (T-C). Turn the
screw in back counter-clockwise to increase support, and clockwise to decrease. Adjust the tilt joint
using 6mm Allen Wrench (T-C).
TV
TV
TV
M-A
M-B
M-C
D
D
T-C
T-C

6
STEP 7
Remove cable cover on Gas Spring Arm (C) using a Phillips screwdriver. Slide cable cover on Lower
Arm (B) forward to remove.
STEP 8
Organize cables, then reinstall cable covers to Gas Spring Arm (C) and Lower Arm (B).
C
B
C
B

7
STEP 9
For safety, please do not extend the monitor behind the desk. This may cause instability and tip the
desk over.
STEP 10
T-C
T-B
T-A
Adjust as desired. Store Allen Wrenches (T-A, T-B, T-C) in Cover (H) for future adjustments.
H

LAST UPDATED: 07/14/2023
REV1
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303