Vivo STAND-V103 User manual

Triple Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v103
SKU: STAND-V103
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualied technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specied in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
A (x1)
Pole
B(x1)
Lower Clamp
C(x1)
Upper Clamp
D(x1)
Pole Cover
E(x1)
Arm
G (x4)
Joint Cover
H(x4)
Plastic Spacer
S-B (x2)
M10x15mm
Screw
S-D (x2)
M8x10mm
Screw
S-F (x1)
M10 Bolt
I (x1)
Support Plate
S-E (x1)
M10 Washer
S-G (x1)
Lock Washer
L (x1)
Grommet Pad
M-A (x12)
M4x12mm
Thumbscrew
M-B (x12)
M4x30mm
Screw
M-C (x12)
M4 Spacer
N (x2)
Spare Cap
T-D (x1)
Wrench
K (x2)
Side VESA Plate
J (x1)
Center VESA Plate
S-I (x2)
Cap Nut
S-H (x1)
M4x6mm
Screw
M (x4)
Cable Clip
F(x2)
Arm Extension
S-C (x2)
M10x47mm
Screw
S-A (x3)
M6x8mm
Screw
T-A (x1)
3mm Allen
Wrench
T-B (x1)
5mm Allen
Wrench
T-C (x1)
6mm Allen
Wrench
NOTE: SOME HARDWARE MAY NOT BE USED

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Install Upper Clamp (C) to Pole (A) using M6x8mm Screws (S-A) and a Phillips
screwdriver. Assemble Lower Clamp (B) to Upper Clamp (C) using M10x15mm
Screws (S-B) and 5mm Allen Wrench (T-B). Secure the clamp assembly to the
desktop be tightening to the hand bolts on Lower Clamp (C). Install the Pole Cover
(D) to Pole (A).
TOOLS NEEDED
Phillips
Screwdriver
OPTION B: Existing Grommet Base Installation
Remove adhesive backing from Grommet Pad (L) and place on the bottom of Pole
(A). Install Pole (A) to existing grommet hole using Support Plate (I) with M10 Bolt
(S-F), M10 Washer (S-E) and Lock Washer (S-G). Tighten
with Wrench (T-D). Install the Pole Cover (D) to Pole (A).
Drill
22 lbs
Per Arm
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
C
A
S-A
B
D
S-B
T-B
S-E
S-G
T-D
S-F
L
A
D
I

4
STEP 1 (Continued)
STEP 2
Align Arm Extensions (F) with Arm (E) so that the holes for the wire clips are
facing down. Place Plastic Spacers (H) on top and bottom of Arm Extensions (F).
Assemble Arm Extensions (F) to Arm (E) with M10x47mm Screws (S-C) and tighten
using 6mm Allen Wrench (T-C). Press Joint Covers (G) into place.
OPTION C: Self-Drilled Grommet Base Installation
Drill a 3/8” (10mm) diameter hole through the mounting surface Remove adhesive
backing from Grommet Pad (L) and place on the bottom of Pole (A). Install Pole (A)
to existing grommet hole using Support Plate (I) with M10 Bolt (S-F), M10 Washer
(S-E) and Lock Washer (S-G). Tighten with Wrench (T-D). Install the Pole Cover (D)
to Pole (A).
S-E
S-G
T-D
S-F
D
I
A
L
F
E
H
S-C
T-C
G

5
STEP 3
Assemble Arm (E) to Pole (A) using M8x10mm Screws (S-D) and 5mm Allen
Wrench (T-B).
STEP 4
OPTION A: Flat Back Monitor
Secure Side VESA Plates (K) to monitors
using M4x12mm Thumbscrews (M-A).
OPTION B: Curved Back Monitor
Secure Side VESA Plates (K) to monitors
using M4x30mm Screws (M-B) and M4
Spacers (M-C).
Secure Center VESA Plate (J) to monitors
using M4x12mm Thumbscrews (M-A).
Secure Center VESA Plate (J) to monitors
using M4x30mm Screws (M-B) and M4
Spacers (M-C).
=
=
E
A
S-D
T-B
KK
M-A
M-A
J
J
M-B
M-B
M-C
M-C

6
STEP 6
Remove the plastic covers on Arm
Extensions (F) and adjust the tilt using
Wrench (T-D).
Adjust the Tilt and rotation of the center
monitor by loosening the set screw on
Arm (E) using 3mm Allren Wrench (T-A).
Retighten the set screw.
Assemble side VESA Plates (K) with
monitors to Arm Extensions (F). Secure
using Cap Nuts (S-I).
STEP 5
Assemble Center VESA Plate (J) with
monitor to Arm (E). Secure using
M4x6mm Screw (S-H).
K
F
S-I
J
E
S-H
F
T-D
T-A
E

7
STEP 7
Adjust the Height of Center Monitor:
Using 6mm Allen Wrench (T-C), turn the
bolt on Arm (E) counterclockwise to
lower the center monitor, turn the bolt
clockwise to raise the center monitor.
Adjust the Height of Side Monitors:
Remove Cap Nut (S-I) from Arm Exten-
sions (F). Turn the screw using counter-
clockwise using 3mm Allen Wrench (T-A)
to raise the monitor, and clockwise to
lower it.
STEP 9
Insert Cable Clips (M) into the undersides of Arm (E) and Arm Extensions (F).
Route cables through Cable Clips (M) and Pole (A).
STEP 8
Remove Joint Covers (G) from Arm (E) to adjust the
tension using 6mm Allen Wrench (T-C).
T-C
EF
T-A
M
EF
A
E
T-C

LAST UPDATED: 06/13/2022
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303