Vivo STAND-V103F User manual

Triple Monitor Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v103f
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V103F

2 3
ASSEMBLY STEPS
STEP 1
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
Phillips
Screwdriver
A (x1)
Pole
B(x1)
Weighted Base
C(x1)
Decorative
Cover
T1 (x2)
VESA Plate
(side)
Q(x2)
Spare Plastic
Cover
K(x1)
Support Plate
S(x1)
Wrench
I (x2)
M8x10 Bolt
O (x12)
M4x30 Bolt
P (x12)
M4 Spacer
M (x1)
Spring Washer
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
N(x12)
M4x12
Thumbscrew
L(x1)
M10 Washer
D1 (x1)
Monitor Arm
(center)
D2 (x2)
Monitor Arm
E (x4)
Monitor Arm
Cover
F(x4)
Plastic Pad
G (x2)
M10x47 Bolt
H (x3)
M6x29 Bolt
J(x1)
M10 Bolt
R(x1)
Allen Key Set
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
T2 (x1)
VESA Plate
(center)
U1 (x2)
Security Nut
U2 (x1)
M4x6 Bolt
V(x4)
Wire Clip
OPTION A: Weight Base Installation
Install the weighted base (B) to the Pole (A) using M6x29 Bolts (H).
Install the Decorative Cover (C).
OPTION B: Grommet Hole Installation
Position the Pole (A) on the mounting surface and mark the
center hole. Drill a 3/8” (10mm) diameter hole at the marked
position through the mounting surface. If using an existing
grommet hole, remove the plastic cover if present to ensure a at
surface before installing the desk mount. Position the Pole (A) on
the mounting surface and secure using the Support Plate (K), M10
Washer (L), Spring Washer (M) and M10 Bolt (J). Fasten the M10
Bolt with provided Wrench (S). Install the Decorative Cover (C).
L
A
C
H
B
K
A
C
J
M
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

4 5
STEP 2
Assemble Monitor Arms (D1,
D2) by placing Plastic Pads (F)
on top and bottom of arms (D2)
and inserting them into center
arms (D1) as shown in diagram.
Secure with M10x47 Bolts (G)
and tighten with Allen Key (R).
Press Monitor Arm Covers (E)
onto top and bottom of arm
joints.
STEP 3
Snap Wire Clips (V) into large holes in Monitor Arms.
Install assembled Monitor Arm to the pole, making sure
the wire clips are facing down. Fasten the M8x10 bolt (I)
using the Allen Key (R).
STEP 4A
Option A: Flat Back Monitor
Fasten the VESA Plates (T1, T2) to monitors using
M4x12 Thumbscrews (N). Do not overtighten;
thumbscrews only need to be ngertight.
Option B: Curved Back Monitor
Fasten the VESA Plates (T1, T2) to monitors using
M4x30 Bolts (O) and M4 Spacers (P).
STEP 5A
Slide the center monitor onto the center head of Monitor Arm. Install the M4x6 Bolt (U2) to secure the
monitor.
STEP 1 (continued)
OPTION C : Grommet Hole Installation w/Base
Position the Pole (A) on the mounting surface and mark
the center hole. Drill a 3/8” (10mm) diameter hole at the
marked position through the mounting surface. If using
an existing grommet hole, remove the plastic cover if
present to ensure a at surface before installing the
desk mount. Install the Weighted Base (B) to the Pole
(A) using M6x29 Bolts (H). Position the Pole (A) on the
mounting surface and secure using the Support Plate
(K), M10 Washer (L), Spring Washer (M) and M10 Bolt (J).
Fasten the M10 Bolt with provided Wrench (S). Install
the Decorative Cover (C). h
A
C
H
B
M
K
J
L
É
D2
D2 G
R
D1
F
N
T1
T1
P
O
E
E
I
ì O
D1, D2
U2

6 7
STEP 6
Adjust the tilt and swivel. Use the Allen Key (R) to adjust swivel joint tension. Use the wrench (S) to
tighten the side tilt joints if the monitors are not fully supported. Fasten the grub screw on back of
center monitor joints if the monitors are not fully supported.
ê
STEP 7
STEP 8
Manage wires. Use clips to secure wires along the arms, and feed wires through the top of the pole
and through the hole in back to hide excess wires.
Turn the bolt on the center of the Monitor Arm counterclockwise to lower the center monitor or
clockwise to raise the center monitor. Remove the security nut (U1) and turn the bolt underneath with
the Allen Key (R) to raise or lower the side monitor. Replace the nut aer adjustment.
STEP 5B
Slide the side monitors onto the heads of Monitor Arm. Install the security nuts (U1) to secure the
monitors.
Grub
Screw
S
R
R
D1, D2
U1

Last Updated: 11/30/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654