Vivo STAND-V101G2 User manual

Pneumatic Arm Dual Monitor Desk Mount with Pull Handle
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101g2
SKU: STAND-V101G2
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1)
Base
B(x1)
Lower Arm
C(x1)
Gas Spring Arm
P (x1)
3mm Allen
Wrench
L (x1)
Clamp
M (x4)
M6x12 Flat
Head Bolt
N (x4)
M6x10 Bolt
O (x2)
M6x22 Bolt
M-A (x8)
M4x12
E(x2)
VESA Plate
G(x1)
Clamp Plate
H (x1)
Grommet
Plate
I(x1)
So Pad
J (x1)
Cover
K (x1)
Clamp
Brace
M-B (x8)
M5x12
M-C (x8)
D5 Washer
D(x1)
Monitor Arm
F (x1)
Handle
R (x1)
6mm Allen
Wrench
Q(x1)
4mm Allen
Wrench

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Attach clamp brace (K) to base (A) using M6x12 flat head bolts (M) and tighten with 4mm Allen
wrench (Q). Apply so pad (I) to underside of base. Install M6x10 bolts (N) to back of clamp (L),
leaving 6mm of thread exposed. For a desk thickness of 3/8” - 2-1/2” (10 - 58mm), hang assembled
clamp into top 4 slots of clamp brace, or for a desk thickness of 2” - 3-3/8” (50 - 85mm), into lower 4
slots. Tighten with 4mm Allen wrench (Q), then place clamp plate (G) on top of clamp bolts. Position
base on desktop and tighten clamp bolts evenly using 6mm Allen wrench (R). Attach cover (J) to
back of clamp brace.
TOOLS NEEDED
Phillips
Screwdriver
2.2-17.6lbs
(1-8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM

4
STEP 1 (Continued)
Attach grommet plate (H) to base
(A) using M6x12 flat head bolts (M)
and tighten with 4mm Allen wrench
(Q). Apply so pad (I) to underside
of base. Position base over grommet
hole in desktop, or drill a 3/8” (10mm)
hole through the desk for installation.
Remove large bolt from clamp (L)
using 6mm Allen wrench (R), then
Insert clamp bolt with clamp plate
(G) up through the underside of the
desk and tighten using the 6mm Allen
wrench (R).
STEP 2
STEP 3
Place lower arm (B) on top of base, and secure by turning the lower screw in back with 3mm Allen
wrench (P). Optionally, also tighten the upper screw to restrict swivel movement to +/-90 degrees.
Place gas spring arm (C) on top of lower arm, and secure by turning the screw in back with 3mm Allen
wrench (P).
OPTION B: Grommet Base Installation

5
STEP 4
Install the VESA plates (G) to monitors using M4x12 bolts (M-A) or M5x12 bolts (M-B) with
washers (M-C), making sure the large end of each bracket in back is facing up.
STEP 5
Mount handle (F) to back of monitor arm using M6x22 bolts (O) to one of the positions shown in the
diagram according to the size of your monitors. Tighten with 4mm Allen wrench (Q).
STEP 6
TV
TV
TV
Install monitor arm (D) to gas spring arm using M6x12 bolts (N) and tighten with
4mm Allen wrench (Q).

6
STEP 7
Place the monitors with VESA plates into the supports on the arm, then turn
the screw on each support to secure the monitors.
STEP 8
If needed, adjust gas spring arm to support the monitors using the 6mm Allen wrench (R). While
holding arm in the straight forward position, turn the screw in back clockwise to decrease support,
and counter-clockwise to increase. Slightly loosen the monitor arm for leveling if needed.
STEP 9
Remove cable cover on upper arm using a Phillips screwdriver. Slide cable cover on lower
arm forward to remove.

7
STEP 10
For safety, please do not extend the monitors behind the desk. This may cause instability and tip the
desk over
STEP 12
Organize cables, then reinstall cable covers to arms.
STEP 11
Turn the screw underneath each monitor support bracket for leveling. Tools may be
stored in the cover (J).

LAST UPDATED: 04/08/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303