Vivo DESK-V133E User manual

Black Electric Multi Motor Corner Desk Frame
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-v133e
SKU: DESK-V133E
[email protected]om www.vivo-us.com 309-278-5303

2
J (x1)
Extension
Cord
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
PACKAGE CONTENTS
WARNING!
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
A (x1)
Telescopic
Crossbar
D(x3)
Liing
Column
F(x1)
Corner Foot
S-A (x12)
M6x10 Bolt
S-B x10)
M6x16 Bolt
S-D (x2)
3/4" Screw
H (x1)
Control Unit
B (x1)
Extension
Crossbar
G(x1)
Fixing Plate
I(x1)
Power Cord
K (x1)
Cable Tray
E(x2)
Foot
C(x3)
Side Bracket
S-F (x4)
M4x5 Bolt
S-G x3)
Cable Clip
S-H (x16)
Anti-Vibration
Pad
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
L (x2)
Hook
S-I (x1)
Allen
Wrench
M (x1)
Control Panel
S-C x16)
7/8" Screw
S-E (x2)
M4x5 Flat Head
Bolt

3
Phillips
Screwdriver
TOOLS
NEEDED
330lbs
(149.69kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Drill
Level
STEP 2
Place the side brackets (C) upside down on a flat surface, then place telescopic crossbar (A) and
extension crossbar (B) over the brackets as shown, making sure the screw posts on the brackets fit
into the holes in the crossbars. Place liing columns (D) on telescopic crossbar, and align the holes
on the end of the extension crossbar with the holes on the center liing column and telescopic
crossbar. Secure the extension crossbar using two M6x12 bolts (S-A) through the side and two M6x16
bolts (S-B) through the crossbar and corner liing column as shown. Secure liing columns with ten
M6x12 bolts (S-A). Attach third liing column to the assembled frame by using four M6x12 bolts (S-A).
Tighten all fourteen bolts with the Allen wrench (S-I).
Loosen all eight set screws
on the telescopic crossbar (A)
and all four set screws on the
extension crossbar (B) using
the Allen wrench (S-I).

4
STEP 3
STEP 6
STEP 5
STEP 4
Place tabletop upside down on the floor.
Place frame assembly upside down on
tabletop, and adjust the crossbars to the
appropriate length.
Tighten all set screws with the Allen wrench (S-I).
Drill 3/8" (10mm) deep pilot holes under the desktop with a 3/32" (or
3mm) drill bit, then remove the frame from the desktop.
Place the feet (E) on the side
columns as shown. Insert
M6x16 bolts (S-B) into the four
mounting holes on each foot and
tighten with Allen wrench (S-I).
Press the corner foot (F) onto the
corner column.

5
STEP 7
STEP 8
Attach the fixing plate (G) to the frame using M4x6
flat head bolts (S-E). Tighten screws with a Phillips
screwdriver.
Connect control panel (M), liing columns (D)
and power cord (I) to the control unit (H). If
needed, use the extension cord (J) to connect the
farthest liing column.
STEP 9
Slide the control unit (H) onto the fixing plate (G) as shown.

6
STEP 10
STEP 11
Fix the hooks (L) to the cable tray (K) with M4x6 bolts (S-F)
and tighten with a Phillips screwdriver. Hang the shelf onto
the frame as shown.
Tighten installed thumbscrews to secure the cable tray (K). Press anti-vibration pads (S-H) into
desktop mounting holes.
STEP 12
Attach the desktop with 7/8" screws (S-C) using a Phillips screwdriver. Place the control panel at the
desired location and mark drilling locations with a pencil. Drill 3/8" (10mm) deep pilot holes under the
desktop with a 5/64" (or 2mm) drill bit. Attach the control panel to the desktop with 3/4" screws (S-D)
using a Phillips screwdriver. Add cable clips (S-G) to organize.

7
STEP 13
Connect the power cable to a wall outlet to power on desk for operation. Each foot pad can be adjusted
independently for fine tuning. Slightly turn the foot pad to lower or raise the base. Use a level to ensure
the desktop is even.
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk weight limit. Keep area of vertical motion free of
obstacles.
Keep weight on desk balanced for
correct operation and longer life of
components.
Leave enough slack in cables to
allow for full range of vertical
motion.

LAST UPDATED: 09/18/2019
Open Monday-Friday from 7:00am-7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times.
If any parts are received damaged or defective, please contact us.
We are happy to replace parts to ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]
www.vivo-us.com
309-278-5303
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
AVG. RESOLUTION TIME (within oice hrs): < 15 M