Volt All-Star Brass Tommy Light User manual

VOLT®Low Voltage Landscape Lighting
LED All Star Tommy Light
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2017, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

VOLT®LED All Star Tommy Light Package Contents
Parts Required (Sold Separately)
Product Dimensions
Important: Please Read Before Installation
Important Safety Instructions
INSTALLATION INSTRUCTIONS
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes
and instructions may result in serious injury, property damage, or void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing
this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet
(3.05M) or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that is suitable
for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm)
7. If additional lengths of low voltage cable is required, please contact
www.voltlighting.com or call 1-813-978-3700.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damage shield.
SAVE THESE INSTRUCTIONS
A. (1) Fixture
A. (3) Self-tapping Screws
B. (3) Wall Anchors
!
!
www.voltlighting.com [email protected] • 813.978.3700
5.00”
2.55”
C. (1) LED MR16 Lamp
Remove Faceplate and Glare Guard
1
Glare Guard
Faceplate
Screw
Fixture
Use a screwdriver to unlock the set
screw. Then, remove the glare guard
from the faceplate. Next, remove the
faceplate from the xture.
3.10”

INSTALLATION INSTRUCTIONS
www.voltlighting.com [e-mail] • 813.978.3700
VOLT®LED All Star Tommy Light
Install Lamp
Install Faceplate and Glare Guard
2
3
Lamp
Set Screw
Socket
Faceplate
Glare Guard
Fixture
Install Fixture
4
Determine your desired location for
the xture. Pass self-tapping screws
through the holes on the surface
mount. Thread self-tapping screws
into the wall surface to secure the
xture.
NOTE: Wall anchors are required
for brick walls or concrete walls.
To determine locations for the wall
anchors, place the surface mount
onto your desired location and
mark the points from the holes in
the mount.
Fixture
Self-tapping Screw
Wall Anchors
Insert lamp with correct wattage
and type marked on xture label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch lamp with
bare hands. Use soft cloth to
handle lamp.
Replace the faceplate over the
lamp and thread onto the xture.
Tighten until snug. Attach the glare
guard back onto the faceplate and
secure with the set screw. Tighten
until snug with a screwdriver.
Wire Connections
5
Lay out the supply cable to the transformer. Strip both leads from the
luminaire pigtail. Connect leads from the supply cable to transformer
(sold separately).
Fixture
Pigtail
Transformer
(Sold Separately)
Supply Cable

INSTALLATION INSTRUCTIONS
www.voltlighting.com
VOLT®LED All Star Tommy Light
Specications and product details subject to change without notice.
© Copyright 2017, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
Adjust Angle of Lamp
6
Install/Replace Lamp
Unscrew the set screw on the glare guard, then remove the glare guard
and faceplate to expose the lamp. Replace it with the correct wattage and
type marked on the xture label. Finally, reinstall the faceplate and glare
guard, then tighten the set screw.
IMPORTANT: Halogen lamps must be protected from moisture and dust at
all times. Always reinstall Faceplates and glare guards immediately.
Knuckle
Adjustment
Loosen the knuckle adjustment
screw and adjust the luminaire to
your desired angle and then tighten
adjustment screw.
is-GGT1-ver1.pdf