Volt VAL-91 Series Operating and safety instructions

Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
Specications and product details subject to change without notice.
© Copyright 2017, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
VOLT®Low Voltage Landscape Lighting
VOLT®Cast Brass Integrated LED Downlight
VAL-91xx Series

VOLT®Cast Brass Integrated LED Downlight
VAL-91xx Series
INSTALLATION & MAINTENANCE GUIDE
www.voltlighting.com
–2–
Important Safety Instructions: Read Before Installation
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that is suitable for
outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminare, or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm)
7. If additional lengths of low voltage cable is required, please contact www.
voltlighting.com or call 1-813-978-3700.
!
SAVE THESE INSTRUCTIONS

[email protected] • 813.978.3700
–3–
–2–
Package Contents
Product Dimensions
A. (1) Luminaire
B. (1) Base
C. (3) Spacer
Install Base
1
Determine the desired location for
mounting the luminaire. Pass self-tapping
screws through the holes on the base and
spacers. Thread the self-tapping screws
into the surface to secure the base.
NOTE: Wall anchors (not supplied) are
required for brick walls or concrete walls.
To determine locations for wall anchors
place the base onto your desired location
and mark points from holes on base.
6 1/2”
6 3/4”
8 3/4”
3 1/4”
5”
D. (3) Self-tapping Screw
E. (1) Optic*
Base
Self-tapping
Screw
Wall Anchor
(not supplied)
Spacer
* Ships with a 60° installed.

VOLT®Cast Brass Integrated LED Downlight
VAL-91xx Series
INSTALLATION & MAINTENANCE GUIDE
www.voltlighting.com
–4–
Install Luminaire to Base
2
Wire Connections
3
Place the luminaire on top of the base
and secure with lock collar. Tighten
until snug.
Luminaire
Pigtail
Base Lock Collar
Strip both of the leads from the luminaire pigtail. Using two wire
connectors (sold separately), connect the leads from the luminaire to
the main low voltage supply cable leads.
Pigtail
Main Low Voltage Supply Cable
Wire Connectors

[email protected] • 813.978.3700
–5–
–4–
Install/Replace Optic
Remove Glare Guard
4
Remove Outer Ring
Replace Optic
5
6
Unscrew the lock screw and remove
the glare guard from the luminaire.
Glare Guard
Lock Screw
Luminaire
Unscrew the lens and remove it from
the luminaire.
Lens
Luminaire
Remove the plug at the center of the
optic. Unscrew the screw and remove
the optic from the luminaire.
Install the new optic in the luminaire.
Reverse Steps 6 and Step 4 to reinstall
removed parts.
Optic Plug
Screw
Luminaire

Specications and product details subject to change without notice.
© Copyright 2017, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
is-val-91xx-ver6