Volt VFL-120V Series User manual

VOLT®Landscape Lighting
LED Floodlights
VFL-120V Series
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2017, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

VOLT®Landscape Lighting
VFL 120V Floodlights
Important: Please Read Before Installation
Important Safety Instructions
INSTALLATION INSTRUCTIONS
1. This LED Floodlight uses the latest in solid state lighting technology for
long life, low maintenance, and high efciency.
2. An internal power-factor-corrected switch mode supply allows this
xture to be used from any nominal 100V-277V, 60Hz AC supply without
any variation in light output.
3. Suitable for use in:
a. Ambient Temperatures of: -20~+40°C (-4~+104°F)
a. Wet Locations
Note: Save these instructions for future reference.
To avoid the risk of re, explosion, or electric shock, this product should
be installed, inspected, and maintained by a qualied electrician only, in
accordance with all applicable electrical codes.
To avoid electric shock:
1. Be certain electrical power is OFF before and during installation and
maintenance.
2. Luminaire must be connected to a wiring system with an equipment-
grounding conductor.
To avoid explosion:
1. Make sure the supply voltage is the same as the rated luminaire voltage.
2. Do not install where the marked operating temperatures exceed the
ignition temperature of the hazardous atmosphere.
3. Do not operate in ambient temperatures above those indicated on the
luminaire.
For supply connections use wire rated for at least 90°C (194°F)
Warning: these luminaire should ONLY be installed by a qualied electrician.
!
!
www.voltlighting.com
- 2 -

Package Contents
Products Model #
A. (1) Lampbody
[email protected] • 813.978.3700
- 3 -
Model Input
Voltage
Power
Factor Watt Input Current Mounting
VFL-4000-LI-ABZ
100-
277V ≥0.95
10W 0.3A
Knuckle
VFL-4003-LI-ABZ 30W 0.5A
VFL-4005-LI-ABZ 50W 0.8A
Product Dimensions
2.75”
4.75” 3.25”
4.5”
VFL-4000-ABZ
9”
VFL-4003-ABZ
3.5”
5”
4.5”
2.75”
7.25”
6.25”
8.5”

www.voltlighting.com
INSTALLATION INSTRUCTIONS
- 4 -
Install Lampbody
1
Pass supply wire from lampbody through the hole on the wall or J box.
Attach the lampbody to the wall and secure with self-tapping screws.
Hand tighten until snug.
NOTE: Wall Anchors are required for brick walls or concrete walls. To
determine anchor locations, place the backplate of the lampbody onto
your desired location and mark points from the holes on the backplate.
Wall
Lampbody
Mark
Product Dimensions - Continued
2.75”
11.5”
7.25”
4.5”
VFL-4005-ABZ
9.25”
10.25”
VOLT®Landscape Lighting
VFL 120V Floodlights
Self-tapping
Screw
Anchor
(Optional)
Supply Wire
Canopy Mount
(Optional)

[email protected] • 813.978.3700
- 5 -
Wire Connections
2
Allow enough wire from the lampbody for adjustment purposes.
Connect wires from the xture into the wiring terminal. The white
wire goes to the “Neutral” terminal;the black wire goes to the
“Live” terminal; and the green wire goes to the “Ground” terminal.
Fix them in place with the connector screws.
Lampbody
Wiring Terminal
Main Supply Cable
Supply Wire
from Luminaire
Adjust Lampbody
3
Adjust the lampbody to your
desired orentation and tighten the
set screw on the knuckle with a
screwdriver.
Wall
Lampbody
Screw