Volt VFL-430-4-BBK User manual

INSTALLATION INSTRUCTIONS
VOLT®LOW VOLTAGE LANDSCAPE LIGHTING
VOLT® Gentle Splash Cast Brass Flood Light & Wall Wash
ITEM: VFL-430-4-BBK
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

INSTALLATION INSTRUCTIONS
VOLT® Gentle Splash Flood Light & Wall Wash VFL-430-4-BBK
IMPORTANT: PLEASE READ BEFORE INSTALLATION
!
IMPORTANT SAFETY INSTRUCTIONS
!
813.978.3700 • [email protected] • www.voltlighting.com
2
This luminaire is intended for installation in accordance with local codes and the
National Electric Code (NEC). Failure to adhere to these codes and instructions may
result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more
from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (transformer)
rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located within 6
inches (15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6 inches
(152 mm)
7. If additional lengths of low voltage cable is required, please contact www.
voltlighting.com or call 1-813-978-3700.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage
lamp.
6. Do not operate the luminaire tting with a missing or damage shield.
SAVE THESE INSTRUCTIONS

PACKAGE CONTENTS
PRODUCT DIMENSIONS
INSTALL STAKE
1
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake is
ush to grade. To avoid damage
to the stake, place a board on top
of the stake while hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
GroundSoil
Stake
813.978.3700 • [email protected] • www.voltlighting.com
3
A. (1) Stake
B. (1) Luminaire
4”
1.5”
2”

Remove Cover and Gasket with Lens
2
Install Bulb
3
INSTALLATION INSTRUCTIONS
VOLT® Gentle Splash Flood Light & Wall Wash VFL-430-4-BBK
813.978.3700 • [email protected] • www.voltlighting.com
4
Loosen the lock screws and remove the cover and gasket
with the lens from the luminaire to expose the socket.
Lock Screw
Cover
Gasket with lens
Socket
Luminaire
Insert the bulb with correct
wattage and type marked on
the luminaire label.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
NOTE: DO NOT touch bulb
with bare hands. Use soft
cloth to handle lamp.
Bulb
Socket

Remove Glare Guard
4
5
813.978.3700 • [email protected] • www.voltlighting.com
5
Decide which lens you would like to use with this xture.
Then install the gasket with your lens of choice back onto the
luminaire and secure with the lock screws.
Lock Screw
Cover
Gasket with lens
Luminaire
Socket
Install Luminaire to Stake
Clear away an area in the
ground at the wireway slot
on top of the stake. Lay the
luminaire pigtail into the
wireway slot and screw the
xture on to the stake. Tighten
the hex nut on the luminaire
against the stake and tighten
until snug.
Luminaire
Hex Nut
Stake
Pigtail
Wireway Slot