Volt RGBW Max All-Star VAL-2045-ABK User manual

VOLT®Low Voltage Landscape Lighting
VOLT®RGBW Max All-Star Integrated LED Spotlight
VAL-2045-ABK
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2020, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

VOLT® RGBW Max All-Star Integrated LED Spotlight
VAL-2045-ABK
INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 2 -
Important: Please Read Before Installation
Important Safety Instructions
!
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL Listed wire connectors that
are suitable for outdoor use.
5. Position the low voltage wire and UL listed wire connector so that
it is located within 6 inches (15.2 cm) from a building structure, a
luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Lamp gets HOT quickly!
2. Do not touch the hot lens, guard or enclosure.
3. Keep lamp away from materials that may burn.
4. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
5. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

Package Contents
[email protected] • 813.978.3700
- 3 -
A. (1) Fixture Body
B. (1) Allen Wrench
C. (1) IR Remote
Product Dimensions
Products Model #
Model Input Voltage Watt Input
Current
15W Spotlight 12V 15W 1.2A
5.6”
6.25”
10.5”

www.voltlighting.com
INSTALLATION INSTRUCTIONS
- 4 -
1
2
3
VOLT® RGBW Max All-Star Integrated LED Spotlight
VAL-2045-ABK
Surface Mount
Mark points for Anchors
Mark three points on the
mounting surface using the
holes on the base as guides.
These marks will be used for
anchors.
Mounting
Surface
Hole
Fixture Body
Base
Install Anchors
Anchor
Drill the proper holes on the
mounting surface for the anchors.
Insert the anchors into the drilled
holes.
Mark
Mounting
Surface
Install Fixture Body
Place the base onto the anchors
and secure with screws.
Fixture Body
Screw
Base
Cable
Wire exit
Mounting
Surface

[email protected] • 813.978.3700
- 5 -
4
5
Wire Connection
Strip both leads from the luminaire pigtail. Using two UL listed wire
connectors (sold separately), connect the leads from the luminaire to
the main supply cable leads.
Pigtail
Supply Wire
from Fixture
Wire Connectors
Main Supply Cable
Adjust Fixture Body
Using the Allen wrench, loosen the
knuckle to adjust the xture to the
desired orientation. Tighten the
knuckle with the Allen key to secure
the xtures adjustment.
Fixture Body
Knuckle Allen Wrench
ROTATE

INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 6 -
1
2
VOLT® RGBW Max All-Star Integrated LED Spotlight
VAL-2045-ABK
Stake Mount
Remove Base
Unscrew the base and remove
it from the xture body.
Fixture Body
Base
Install Stake and Conduit
Stake
Stabilizer Grid Conduit
Ground Level
Dig a hole in the ground for the conduit runs and the stake. Install
the conduit. Slide the stabilizer grid onto the stake and secure with
the screws. Place the stake over the conduit runs. Backll against the
mounting stake.

[e-mail] • 813.978.3700
- 7 -
3
4
Remove Cap from Stake
Screw
Cap
Stake
Remove the cap from the stake
by loosening the set screws.
Install Cap to Fixture
Fixture
Cap
Thread the cap onto the xture
body and hand tighten until
snug.

INSTALLATION INSTRUCTIONS
www.voltlighting.com
5
- 8 -
VOLT® RGBW Max All-Star Integrated LED Spotlight
VAL-2045-ABK
Wire Connection and Install Fixture to Stake
Screw
Cap
Stake
UL Listed Wire
Connector
Supply Wires
Fixture
Wires
Allow enough wire from the
xture for adjustment purposes.
Strip both leads from the xture
pigtail. Using two UL listed wire
connectors (sold separately),
connect the leads from the
xture to the main supply cable
leads. Place the wire into the
stake and attach the cap back
onto the stake using the screws.
6
Adjust Fixture Body
Using Allen wrench, loosen the
knuckle to adjust the xture to the
desired orientation. Tighten the
knuckle after the adjustments are
made.
Fixture Body
Knuckle Allen Wrench
ROTATE

[e-mail] • 813.978.3700
- 9 -
1
IR Remote
An IR Remote is suitable for this xture. Please refer to the following
instructions for usage and battery replacement.
Remove Plastic Film
CR2025
RELEASE
OPEN
PUSH
Backing
Plastic Film
IR Remote
Remove
Remove the plastic lm from
the IR remote before use.

INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 10 -
VOLT® RGBW Max All-Star Integrated LED Spotlight
VAL-2045-ABK
2
IR Remote Functions
1. On/Off
2. Brightness Control
3. 16 color selections
4. Flash
◗Mode 1: Repeats Red, Green, Blue + color cycle for 1 second duration of
each of the seven colors within this mode.
◗Mode 2: Hit ash a second time and this mode slowly blends the same
seven colors from mode one, mixing them together.
5. Strobe
◗Mode 1: Pick any color on the remote, then press strobe and that color
will strobe every second alternating between on and off.
◗Mode 2: Hit strobe a second time and this mode will strobe a blended
white color at the same speed as before.
6. Fade
◗Mode 1: Pick any color on the remote, then press fade and that color
will slowly fade in and out every second.
◗Mode 2: Hit fade a second time and it will fade a blended white color in
and out at the same speed as before.
7. Smooth
◗Mode 1: Repeats a ash cycle of Red, Green, and Blue only.
◗Mode 2: Hit smooth a second time and this mode slowly blends Red,
Green, and Blue only; in and out of each other at the same speed.
NOTE: When using the
remote make sure it is
pointed at the sensor on
the back of the xture so it
operates properly.