Volt VAC-AL-GGT1-BBZ User manual

VOLT®Low Voltage Landscape Lighting
VOLT® All-Star Tommy Light
VAC-AL-GGT1-BBZ
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

VOLT®All-Star Tommy Light
VAC-AL-GGT1-BBZ
Important: Please Read Before Installation
Important Safety Instructions
INSTALLATION INSTRUCTIONS
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes
and instructions may result in serious injury, property damage, or void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet
(3.05M) or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that
are suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable is required, please contact
www.voltlighting.com or call 1-813-978-3700.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
!
!
www.voltlighting.com

Package Contents
Parts Required (sold separately)
Product Dimensions
A. (1) Fixture
A. (3) Self-tapping Screws
B. (3) Wall Anchors
[email protected] • 813.978.3700
5.00”
2.55”
C. (1) LED MR16 Lamp
Remove Lens and Glare Guard
1
Glare Guard
Lens
Screw
Fixture
Use a screwdriver to loosen the set
screw. Then, remove the glare guard
from the lens. Next, remove the lens
from the xture.
3.10”

VOLT®All-Star Tommy Light
VAC-AL-GGT1-BBZ
Install Lamp
Install Lens and Glare Guard
2
3
Lamp
Set Screw
Socket
Lens
Glare Guard
Fixture
Insert the lamp with correct
wattage and type marked on the
xture label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch lamp with
bare hands. Use soft cloth to
handle lamp.
Place the lens over the lamp and
thread onto the xture. Tighten
until snug. Attach the glare guard
back onto the lens and secure with
the set screw. Tighten until snug
with a screwdriver.
INSTALLATION INSTRUCTIONS
www.voltlighting.com

[email protected] • 813.978.3700
Install Fixture
4
Determine your desired location for
the xture. Pass self-tapping screws
through the holes on the surface
mount. Thread self-tapping screws
into the wall surface to secure the
xture.
*This xture must be installed
under an eave or overhang.
NOTE: Wall anchors are required
for brick walls or concrete walls.
To determine locations for the wall
anchors, place the surface mount
onto your desired location and
mark the points from the holes in
the mount.
Fixture
Self-tapping Screw
Wall Anchors
Wire Connections
5
Fixture
Pigtail
Transformer
(sold separately)
Supply Cable
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold separately), connect the leads from the luminaire to the main
supply cable leads.

VOLT®All-Star Tommy Light
VAC-AL-GGT1-BBZ
Adjust Angle of Lamp
6
Install/Replace Lamp
Loosen the set screw on the glare guard, then remove the glare guard and
lens to expose the lamp. Replace it with the correct wattage and type
marked on the xture label. Finally, reinstall the lens and glare guard, then
tighten the set screw.
IMPORTANT: Bulbs must be protected from moisture and dust at all
times. Always reinstall lens and glare guards when removed.
Knuckle
Adjustment
Loosen the knuckle and adjust the
luminaire to your desired angle and
then tighten adjustment screw.
INSTALLATION INSTRUCTIONS
www.voltlighting.com

[email protected] • 813.978.3700

is-VAC-AL-GGT1-BBZ-ver1.pdf
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz, FL USA 33549 • All rights
reserved [email protected] • 813.978.3700
www.voltlighting.com