Volt 130 Series Operating and safety instructions

VOLT®Low Voltage Landscape Lighting
The Tank
130 Series
Installation & Maintenance Guide
Specications and product details subject to change without notice.
© Copyright 2014, VOLT®Lighting, Lutz FL USA 33549 • All rights re-
served. [email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

VOLT®The Tank
130 Series
Important: Please Read Before Installation
IMPORTANT SAFETY INSTRUCTIONS
INSTALLATION INSTRUCTIONS
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and instruc-
tions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (trans-
former) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that is suitable
for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm)
7. If additional lengths of low voltage cable is required, please contact
www.voltlighting.com or call 1-813-978-3700.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may dam-
age lamp.
6. Do not operate the luminaire tting with a missing or damage shield.
SAVE THESE INSTRUCTIONS
!
!
www.voltlighting.com

Product Dimensions
A. (1) Stake
B. (1) Luminaire
C. (1) Shield
Install Stake
1
[e-mail] • 813.978.3700
Determine desired location for mounting lumi-
naire. Hammer stake into ground until ange
of stake is ush to grade. To avoid damage to
stake, place board on top of stake while ham-
mering.
NOTE: If ground is hard and stake is difcult to
install, make a crosscut in ground using a at
shovel.
Board
Stake
Soil
Ground
Package Contents
6”
2 1/2”
4 1/2”
2 1/4”

INSTALLATION INSTRUCTIONS
www.voltlighting.com
VOLT®The Tank
130 Series
Wire Connections
3
Strip two leads from luminaire pigtail. Using two wire connectors, sold
separately, connect leads from luminaire to main low voltage supply
cable lead.
Luminaire Wires
Main Low Voltage
Supply Cable
Wire
Connectors
Clear away area in ground at wireway
slot in top of stake. Lay luminaire
pigtail into wireway slots and screw
luminaire into stake.
If using optional stake cover, sold
separately, align the wireway slots on
stake cover and stake before screw-
ing luminaire into stake.
Use included locknut to secure the
luminaire position.
Install Luminaire to Stake
2
Luminaire
Stake Cover
Stake
Pigtail
Wireway Slot

[e-mail] • 813.978.3700
Install Shield to Luminaire
Install Lamp
5
4
Thread shield onto luminaire. Hand
tighten until snug. Adjust the luminaire
to desired angle by using adjustment set
screw.
Insert lamp, sold separately, with
correct wattage and type as marked on
luminaire label.
CAUTION: Do not exceed maximum watt-
age marked on luminaire label.
NOTE: DO NOT TOUCH halogen lamp
with bare hands. Use soft cloth to han-
dle lamp.
Shield
Luminaire
Socket
Lamp
Maintenance - Lamp Replacement
Unscrew shield to expose lamp then replace it with correct wattage and
type as marked on luminaire label. Reinstall shield to luminaire.
IMPORTANT: Halogen lamps must be protected from moisture and dust at all
times. Always reinstall shield when moved.
Set Screw

is-130-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2014, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com