Volt BRASS BULLY VWL-5 Series User manual

VOLT®Low Voltage Landscape Lighting
Brass Bully Well Lights
INSTALLATION INSTRUCTIONS
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

VOLT®Brass Bully Well Lights
Important: Please Read Before Installation
IMPORTANT SAFETY INFORMATION
INSTALLATION INSTRUCTIONS
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that is suitable for
outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm)
7. If additional lengths of low voltage cable is required, please contact
www.voltlighting.com or call 1-813-978-3700.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage
lamp.
6. Do not operate the luminaire tting with a missing or damage shield.
SAVE THESE INSTRUCTIONS
!
!
www.voltlighting.com

Package Contents
Product Dimensions
A. (1) Housing
B. (1) Luminaire Cover with
Gasket
[e-mail] • 813.978.3700
Brass Bully Open
550
Brass Bully Beacon
553
Brass Bully Grate
552
Brass Bully Shielded
554
5”
4.5”
5.5”
C. (5) Lock Screws
Brass Bully Turret
VWL-555

INSTALLATION INSTRUCTIONS
www.voltlighting.com
VOLT®Brass Bully Well Lights
Strip two leads from luminaire
pigtail. Using two wire connectors,
sold separately, connect leads from
luminaire to main low voltage supply
cable leads.
Wire Connection
2
Pigtail
Wire Connector
Main Low Voltage
Supply Cable
Install the luminaire in hole and ll
hole with pea gravel or sand.
Fill Pea Gravel or Sand
3
Pea Gravel
or Sand
Luminaire
Soil
3”
3”
3”
Dig Hole
1
Dig hole in the ground. Make sure
there is approximately 3” space
surrounding the luminaire housing for
pea gravel or sand.
Luminaire
Hole
Soil

[e-mail] • 813.978.3700
Insert MR16 lamp with correct
wattage and type as marked on
luminaire label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch lamp with
bare hands. Use soft cloth to handle
lamp.
Place luminaire cover with gasket
onto housing and secure with lock
screws.
Install Lamp
Install Luminaire Cover with Gasket
4
5
Lamp
Lock Screw
Socket
Luminaire
Cover with
Gasket
Housing
Install/Replace Lamp
Please reverse Step 4 - Step 5 to expose the bulb and replace it with correct
wattage and type marked on luminaire label. Reinstall luminaire cover.
IMPORTANT: Halogen lamps must be protected from moisture and dust at all
times. Always re-install luminaire cover when moved.

is-brassbully-ver2.pdf
Specications and product details subject to change without notice.
© Copyright 2015, VOLT®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)