Volt Belladonna LED Path/Area User manual

VOLT®Low Voltage Landscape Lighting
Belladonna LED Path/Area
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2014, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

VOLT®Belladonna LED Path/Area
VL-1024
Important: Please Read Before Installation
INSTALLATION INSTRUCTIONS
This xture is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, oper-
ation maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing
this xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply (trans-
former) rated maximum of 50 watts (25 AMPS) at 12 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm)
in order to connect to the main low voltage cable.
5. Wiring connections must be made with wire connectors that is suitable
for outdoor use.
6. Position the wire connector so that it is located within 6 inches (15.2
cm) from a building structure, a luminaire, or tting.
!
www.voltlighting.com
Important Safety Instructions
LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn o/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.
!

Package Contents
Product Dimensions
A. (1) Fixture Body
B. (1) LED Bulb
[e-mail] • 813.978.3700
11.25”
8”
3.5”
26.5”
C. (1) Diuser
Parts Required
A. (1) Stake (Sold Separately) B. (1) Base (Sold Separately)
Install Stake
1
Determine desired location for mounting
xture. Hammer stake into ground until
ange of stake is ush to grade. To avoid
damage to stake, place a board on top of
stake while hammering.
NOTE: If ground is hard and stake is dicult
to install, make a crosscut in ground using a
at shovel.
Board
Stake (Sold
Separately)
Soil
Ground

INSTALLATION INSTRUCTIONS
www.voltlighting.com
VOLT®Belladonna LED Path/Area
VL-1024
Install Fixture Body to Stake
2
Clear away area in ground at wireway
slot in top of stake. Align the wireway
slots on base and stake. Lay luminaire
pigtail into wireway slots and thread
the nipple at the bottom end of the
xture body into stake. Tighten until
snug to secure base.
Wire Connection
3
Fixture Body
Base
Stake
Pigtail
Wireway Slot
Strip two leads from luminaire pigtail. Using two wire connectors (not
provided), connect leads from luminaire to main supply cable leads.
Pigtail
Main Supply Cable
Wire Connectors

Install Bulb
Install Diuser
4
5
Insert bulb with correct wattage and
type marked on xture label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch bulb with bare
hands. Use soft cloth to handle bulb.
Remove screws from the shade. Attach
the diuser onto the shade and secure
with the screws previously removed.
[e-mail] • 813.978.3700
Socket
Shade
Bulb
Diffuser
Screw
Install/Replace Bulb
Please reverse Step 5 - Step 4 to expose the Bulb and replace it with correct
wattage and type marked on xture label. Reinstall Diuser.
IMPORTANT: LED Bulb must be protected from moisture and dust at all
times. Always re-install diuser when moved.

IS-VL1024.pdf
Specications and product details subject to change without notice.
© Copyright 2014, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)