Volt VAL-2000-4-BBZ User manual

VOLT®Low Voltage Landscape Lighting
VOLT® All-Star™ Spotlight
VAL-2000-4-BBZ
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

VOLT®All-Star™ Spotlight
VAL-2000-4-BBZ
Important: Please Read Before Installation
IMPORTANT SAFETY INSTRUCTIONS
INSTALLATION INSTRUCTIONS
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.voltlighting.com or call 1-813-978-3700.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
!
!
www.voltlighting.com [email protected] • 813.978.3700
Package Contents
A. (1) Fixture
Parts Required
A. (1) MR16 Lamp (sold separately)
Product Dimensions
2.65”
2.6”
4.25”
1.56”
Remove Glare Guard and Shield from Fixture
1
Glare Guard
Lock Screw
Shield
Fixture
Unlock the lock screw and remove the
glare guard from the shield. Unscrew the
shield and remove it from the xture.
- 2 - - 3 -

INSTALLATION INSTRUCTIONS
www.voltlighting.com [email protected] • 813.978.3700
VOLT®All-Star™ Spotlight
VAL-2000-4-BBZ
Install MR16 Lamp
Install Glare Guard and Shield to Fixture
2
3
Insert the lamp with the correct
wattage and type as marked on the
xture label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch lamp with bare
hands. Use soft cloth to handle lamp.
Screw the shield back onto the
xture. Pass the glare guard over
the shield and secure with the
lock screw. Tighten until snug.
Socket
MR16 Lamp
(sold separately)
Install/Replace Lamp
Remove the glare guard and the shield to expose the lamp and
replace it with the correct wattage and type marked on the xture
label. Then reinstall the shield and glare guard to the xture.
IMPORTANT: Halogen lamps must be protected from moisture and
dust at all times. Always reinstall shield when moved.
Wire Connections
6
Strip both leads from the xture pigtail. Using two wire
connectors (sold separately), connect the leads from the xture
to the main low voltage supply cable lead.
Pigtail
Main Supply Cable
Wire Connectors
Clear away an area in the
ground at the wireway slot
on top of the stake. Lay
the luminaire pigtail into
the wireway slot and screw
the xture onto the stake.
Tighten until snug.
Install Fixture to Stake
5
Fixture
Pigtail
Wireway Slot
Install Stake
4
Board
Stake
Stake
Soil
Ground
Determine the desired location for
mounting the xture. Hammer the stake
into the ground until ange of stake is
ush to grade. To avoid damage to the
stake, place a board on top of the stake
while hammering.
NOTE: If the ground is hard and the
stake is difcult to install, make a
crosscut in the ground using a at
shovel.
Glare Guard
Lock Screw
Shield
Fixture
- 4 - - 5 -

www.voltlighting.com [email protected] • 813.978.3700
- 6 - - 7 -

is-val-2000-ver3.pdf
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
www.voltlighting.com
- 8 -