Vonets VGA1000 User instructions

VONETS 450M 5G+300M 2.4G High Power WiFi bridge, repeater
1
Professional 2.4G/5G High WiFi
Repeater
PM2.4G/PM5G
VGA1000/VGA2000
Quick Setting Guide

VONETS 450M 5G+300M 2.4G High Power WiFi bridge, repeater
2
Declaration
Copyright © 2016 Shenzhen HouTian Network Communication Technology Co.Ltd
All rights reserved, with retained ownership
Without Shenzhen HouTian Network Communication Technology Co.Ltd written
authorization, any company or personal can’t copy, writer or translation part or all
contents. Can’t do commodity distribution for any commercial or profitable purposes
by any ways(electricity, mechanical, photoprint, record or other methods).
VONETS is the registered trademark of Shenzhen HouTian Network Communication
Technology Co.Ltd. The other all trademarks or registered trademarks mentioned in
this documents are belong to the individual owners. The product specifications and
information technology mentioned in this manual are just for reference, if any updates,
without other notice. Except for special agreements, this manual is just for user
guidance, any statements, information and so on in this manual can’t constitute the
warranty of any forms.

VONETS 450M 5G+300M 2.4G High Power WiFi bridge, repeater
3
Product Selection Form
Model
PM5G
VGA1000
PM2.4G
VGA2000
Module or
Finished product
Module
Finished product
Module
Finished product
Built-in battery
None
Built-in 6000mAH
lithium battery
None
Built-in 6000mAH
lithium battery
Supply
Voltage/Current
5V/3A
4.2V Lithium
battery-powered
5V/3A
4.2V Lithium
battery-powered
Ethernet Port
Requires an
external network
transformer to use
None
Requires an external
network
transformer to use
None
Pairing method
WEB Settings
WEB Settings
Main Application
Long distance WiFi transmission or WiFi coverage
1. Long distance WiFi camera
2. UVA figure transmission
3. Long distance fast-networking projects
Working Mode
Repeater + Bridge
Repeater + Bridge
5G Transmission
Power
25.8dbm--27dbm
25--27dBm
Point to point
barrier-free
transmission
500m--800m
1200m--2000m
Transmission
Rate
2.4G 300Mbps, 5G 450Mbps
300Mbps
2.4G Antenna
Gain
1.0dbi--1.5dbi
4.5dbi--5dbi
5G Antenna Gain
4.5dbi--5dbi
None
Temperature
compensation
Support
Support
VONETS High power series WiFi product Features
PM5G/VGA1000 is dual band WiFi Repeater product, support both 2.4G and 5G
Band. 2.4G band is normal power, barrier-free transmission distance is up to 100
meters; 5G band is high power, barrier-free transmission distance is up to 1000
meters, in the unmanned aerial vehicle on the measured distance of 800 meters;
VGA2000 is 2.4G WiFi Repeater product, the transmission power is up to 26dbm,
barrier-free transmission distance is up to 2000 meters;
VGA1000/PM5G are mainly used for long distance network data transmission and

VONETS 450M 5G+300M 2.4G High Power WiFi bridge, repeater
4
wide range of WiFi signal coverage, support both bridge and repeater function;
VGA1000/PM5G, PM2.4G/VGA2000, (it is best to use them in pairs), are mainly
used for long distance WiFi cameras and UAV figure transmission application,
software configuration is so easy:
1) VGA1000 connects to PM5G in pairs;
2) VGA1000 is for ground station, PM5G is air module or remote module;
3) VGA1000/PM5G support hot name name imitate function
4) Multiple VGA1000 or PM5G can form star network;
5) The usage of VGA2000 and PM2.4G is the similar as the above four points;
VGA1000/PM5G, PM2.4G/VGA2000 are all transparent bridge, but transparent
transmission is only for IP layer packets, for the link layer (MAC layer) of the
packet will be MAC address translation. For network devices that use MAC
layer addressing at the link layer, it may not be fully applicable.
VGA1000/VGA2000 are both built-in battery, suitable for mobile portable
applications, to facilitate rapid long-distance emergency network;
Support temperature compensation, to ensure that the performance of industrial
equipment for a long time and stable operation;
All modules provide UART port with standard TTL level, is convenient for secondary
development;
Module with so small size: 30mm*60mm*1.6mm.
VONETS High Power Series WiFi Product Appearance
PM5G/PM2.4G product structure and PIN definition, see the diagram below:
(The thickness of module board 1.6mm+-10%, for detailed dimensions, please see the
CAD file from the official website)
Diagram 1

VONETS 450M 5G+300M 2.4G High Power WiFi bridge, repeater
5
VGA1000/VGA2000 Appearance
PM5G/PM2.4G Module Quick Setting Guide
Step1. Connect --When configuration, the connection method is as below diagram:

VONETS 450M 5G+300M 2.4G High Power WiFi bridge, repeater
6
Step 2. The module is powered on (For module supply voltage, current, please
check <Product Selection Form>, PIN definition, please see Diagram 1)
Step 3. Connect the WiFi hot spot of module by smart phone or PC
(There are two hot spot 2.4G and 5G hot spot, you can choose any one to
connect)
WiFi hot spot parameters of module is as below:
WiFi SSID: VONETS_******
WiFi Password: 12345678
Step 4. Log in WEB configured page, configure the parameters of source WiFi
hot spot
(The default work mode of PM2.4G/PM5G is bridge mode)
1) Open browser (IE, Google Chrome, Safari, the mobile phone browser and so on),
enter IP address (192.168.254.254) or configured domain name of configured page
(http://vonets.cfg)
2) Enter user name and password (it is admin) on the log in page, click “Login” button
to enter configured page;
3) Search the source WiFi hot spot

VONETS 450M 5G+300M 2.4G High Power WiFi bridge, repeater
7
4) Set up the source WiFi hot spot password, extended WiFi hot spot SSID
5) Reboot the device, the device will automatically connect to the configured WiFi hot
spot, if it is configured successfully, the green indicator will flash quickly.
Note 1: When bridge/repeater product are connected to external network, the IP
address of the device will change. At this time, when log in configured page, we
suggest you enter configured domain name: http://vonets.cfg. Or in Windows
command window, enter the command: ping vonets.cfg, to get the IP address of the
device, then log in configuration page with this IP.
Note 2: The optional channel of 5G WiFi is: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104,
108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 161, 165, factory default is the best
channel -- 149.

VONETS 450M 5G+300M 2.4G High Power WiFi bridge, repeater
8
VGA1000/VGA2000 Series Product Introduction
VGA1000/VGA2000 is high power WiFi Repeater, bridge, is also can be used for remote
camera connection, the performance of wireless transmission is consistent with
PM5G/PM2.4G, but it is built-in battery, suitable for mobile portable applications, to
facilitate rapid long-distance emergency network; the below VGA is for VGA1000 and
VGA2000.
VGA Power indicator as below form:
VGA common operation as below form:
Power indicator light
Power
<15%
15%-25%
25%-50%
50%-75%
75%-100%
VGA normal operation form
Operation
Step
LED Status
Time
required
Remark
Power on
Long press 3 seconds
The battery indicator
flashes in a flowing
state
50S
Start complete, stop flashing,
the normal display of the
current battery power
Power off
Quick Click
The power indicator
light goes out
Factory
Reset
1. First, make the device
boot normally;
2. Long press 2 seconds,
the indicator will flash;
3. Within 2 seconds,
press twice again
The battery indicator
flashes in a flowing
state
85S
In the recovery, the device
can’t be shut down, power off
the device will lead to burn
Power
Display
In the off state, short
press the button
Display the current
battery power
It is recommended that only
one cell power left, then
charge the device

VONETS 450M 5G+300M 2.4G High Power WiFi bridge, repeater
9
VGA Quick Setting Guide
Step1. Connect --When configuration, the connection method is as below diagram:
Step 2. VGA is powered on--Operate the device according to <VGA normal
operation form>
Step 3. Connect the WiFi hot spot of VGA by smart phone or PC
(There are two hot spot 2.4G and 5G hot spot, you can choose any one to
connect)
WiFi hot spot parameters of module is as below:
WiFi SSID: VONETS_******
WiFi Password: 12345678
Step 4. Log in WEB configured page of VGA, configure the related parameters
of source WiFi hot spot
1) Open browser (IE, Google Chrome, Safari, the mobile phone browser and so on),
enter IP address (192.168.254.254) or configured domain name of configured page
(http://vonets.cfg)
2) Enter user name and password (it is admin) on the log in page, click “Login” button
to enter configured page;

VONETS 450M 5G+300M 2.4G High Power WiFi bridge, repeater
10

VONETS 450M 5G+300M 2.4G High Power WiFi bridge, repeater
11
VGA1000/VGA2000 Indicator Light Instruction
WiFi Status Light
Hot spot connection Status
Remark
(Green light) Quick Flash
Not connected
Products are not connected to
any hot spots
(Green Light) Quick Flash
Connected
WiFi hot spot signal >50%
(Green Light)
Intermittent Quick Flash
Connected
WiFi hot spot signal is 10%-50%
(Green Light) Slow Flash
Connected
10%WiFi hot spot signal is less
than 10%
(Green Light) Slow Flash
Connection failed
Products are not connected to
any hot spots
General operation and common faults of
VGA/PM5G/PM2.4G Series Products
1. How to reset to the factory default parameters of VGA?
Power on the device, after 50 seconds, first, make the device boot normally; long press
3 seconds until the indicator light flash, after flashing, quick press twice, the battery
indicator flashes in a flowing state, it will take about 85 seconds.
During the recovery of the factory operation, the product can’t be powered off,
otherwise it may cause damage to the product.
2. How to reset the factory default parameters of PM5G/PM2.4G?
Power on the device, after 50 seconds, long press reset button (or connect Reset PIN
of module to GND) 3 seconds, then release, module will factory reset, it will take 85
seconds, during the recovery of the factory operation, the product can’t be powered off,
otherwise it may cause damage to the product.
3. Does the VONETS series product support firmware upgrade, how to upgrade?
All VONETS series products support firmware upgrade, and support online upgrade,
please visit website: www.vonets.com to refer to the related documents.
4. The WiFi hot spot of VGA/PM5G/PM2.4G can be found, but the smart phone or PC
can’t connect to this device hot spot?
Reason 1. Due to some unexpected operation or power down, caused the
destroy of device parameters. At this time, just need to reset the device to
factory default parameters;
Reason 2. Poor power supply performance of the device will seriously

VONETS 450M 5G+300M 2.4G High Power WiFi bridge, repeater
12
affect the WiFi connection performance, or even damage the device,
so we suggest high quality power supply, recommand the total input power is
5V/3A(15W), Ripple less than 100mV power supply. For module, please
make sure use dual power supply (5V/1A, 5V/2A) according to PIN
definition.
5. The device has been configured the source WiFi hot spot parameters, the smart
phone or PC has connected to the device WiFi hot spot, but still doesn’t get internet?
First, check the status light to know the current state of the device, then according
to the state of the device to analyze the fault reasons;
Reason 1. The distance between the device and source WiFi hot spot is too long,
cause the communication performance degradation, finally effect the user’s access
to the Internet. At this time, just need shorten the distance between the device
and source WiFi hot spot to solve this problem;
Reason 2. Due to some unexpected operation or power down, caused the destroy
of device parameters. At this time, just need to reset the device to factory default
parameters;
Reason 3. The configured source WiFi hot spot parameters are not correct. At this
time, just need to configure the correct parameters then reboot the device;
6. The smart phone or PC has been connected the device by WiFi or Ethernet cable,
but user can’t log in the device WEB page, or after log in the WEB it shows error?
Reason 1. The users don’t use the browser recommended by VONETS(IE, Google
Chrome, Safari, the mobile phone browser);
Reason 2. The smart phone or PC installed the firewall, the security level is set too
high, caused the above problem. At this time, only need to close the firewall;
Reason 3. The security level of browser is too high, it will also cause the above
problem. At this time, just need to reduce the browser’s security level, then log
in again;
Reason 4. The IP address of the device input error. For devices that are in use,
the IP address of the device is automatically assigned by the source hot spot, so
the IP address will change, at the same time, you can review “Note 1” to obtain IP
address; for the new factory equipment, users only need to enter the correct
default IP, VGA series default IP is 101.12.30.56, PM5G / PM2.4G the default IP is
192.168.254.254.
Shenzhen Houtian Network Communication Technology Co.,Ltd
http://www.vonets.com