VSpeak Pulse Generator User manual

Pulse Generator Version: 1.0 www.VSpeak-modell.de Page 1/4
Pulse Generator
Manual Version 1.0
Introduction
22 mm
30 mm
As the name already suggests, the pulse generator can be used to
generate ON / OFF pulses in the model. Both the times for the
ON and OFF duration can be set, as well as the ON and OFF
positions. With a 3 step switch, from the transmitter can then
select the respective operating mode between OFF, PULSE and
ON.
One possible application would be e.g. the control of a smoke
pump, in flight would thus be "smoke clouds" of equal length and
at equal intervals possible.

Pulse Generator Version: 1.0 www.VSpeak-modell.de Page 2/4
1Connection
1.1 Input
The pulse generator is plugged with its servo plug either at any receiver power slot, or at the
PowerBox system at the slot designated P²-Bus, . . . or for programming:
on a JetiBox or –
using the JetiBox emulation of a Jeti DC / DS transmitter - with
ext. marked slot of the Jeti receiver
For the relevant servo channel, a 3-step switch can now be programmed in the transmitter with
the values -100% (OFF) 0% (PULSE) +100% (ON).
1.2 Output
In principle, all devices that are otherwise directly plugged into a servo slot of the receiver can
be connected to the output, the 3-pin post connector.
Attention: The pin marked + has the same voltage as the input, ie. When the output is not
connected, special care must be taken with regard to a short circuit.
1.3 LED Indicator
LED: green(ON) →servo output position ON
green (flashing) →servo output in PULSE operation, with the LED ON time
corresponding to the servo output ON duration
red (ON) →servo output position OFF
red (flashing) →only if the JetiBox is plugged in to program the ON / OFF times:
Display of the ON duration
The blue LED is blinking every second to signal the normal function of the
Pulse Generator.
blue LED
LED green/red
Servo output

Pulse Generator Version: 1.0 www.VSpeak-modell.de Page 3/4
2Parameterization
With a JetiBox, a JetiBox emulation of a Jeti DC / DS transmitter or with the PowerBox core,
settings can be made to the pulse generator.
The values shown in the pictures are the set values at delivery.
Example JetiBox emulation:
The parameter selection is done with the button or
Value change with the buttons: : resp.
Example PowerBox
With the PowerBox system, the same settings as with the JetiBox are possible via the
P²-Bus. In addition, you can also select the servo channel (1 ... 26), with which the Pulse
Generator is controlled, and the setting of the priority for the status telemetry value. It can
be chosen between: low / high / higher / at highest . . . where low is sufficient.
The status displays the current switch position: OFF, PULSE or ON.
ON / OFF –servo output ON position
-150 . . . +150 %
ON / OFF –servo output ON duration
0,1 . . . 5,0 s

Pulse Generator Version: 1.0 www.VSpeak-modell.de Page 4/4
3Technical data
Power supply
3,5 … max. 15V from receiver
Current consumption
~20 mA (at 7,4V)
Dimensions
30 x 22 x 4 mm
Weight
~7 g (incl. connection cable)
Connection
UNI servo plug (cable length ~ 30 cm)
4Instructions for disposal
Equipment marked with the symbol should not be disposed of within household
waste.
5EG Declaration of Conformity
Manufacturer
VSpeak-Modellbau (Volker Weigt)
Priestewitz
We hereby declare that the product
VSpeak Pulse Generator
complies with the following European directives:
2004/108/EC EMC Directive
2006/95/EC Low Voltage Directive (LVD)
2011/65/EC Restriction of Hazardous Substances (RoHS)
The presumption of conformity is taken by applying the following harmonized standards:
EN60065 Audio-, video- and similar electronic aparatus - Safety requirements
EN60332 Tests on electric and optical fibre cables under fire conditions
EN60950 Information technology equipment - Safety
EN61000-6-1 Electromagnetic compatibility (EMC)
EN61000-6-3
EN55022 Information technology equipment - Radio disturbance characteristics
Priestewitz, 2019/11/01 .................................................
Signature
Volker Weigt
Managing Director
6Contact
Volker Weigt
www.VSpeak-Modell.de
mail: [email protected]