W & A Delta Plow User manual

DELTA PLOW
OWNER’S MANUAL
Revised 11.20
308.708.8185 | [e-mail] | Manual Part Number - 123009 | Rev. 11/20

2
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
MODEL NUMBER
SERIAL NUMBER
DATE PURCHASED
The serial number plate is located on the frame to be readily available. It is suggested that your serial
number and purchase date also be recorded above.
The serial number poriveds important information about your Delta Plow and may be required to obtain
the correct replacement part. Always provide the model number and serial number to yourW&A Manufacturing
dealer when ordering parts or anytime correspondence is made with W&A Manufacturing.
SERIAL NUMBER
Record the model number and serial number of your Delta Plow along with date purchased:
This manual is applicable to: Delta Plow
Serial Number Plate
Location

3
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
Factory to Farm™ service includes full factory assembly. Dealer is responsible for eld readiness.
TO THE DEALER
PREDELIVERY CHECKLIST
All working parts move freely, bolts are tight, and cotter pins are spread.
Check for oil leaks and proper hydraulic operation.
Hydraulic hoses correctly routed to prevent damage.
Inate tires to specied air pressure and torque wheel lug bolts and lug nuts as specied in the manual.
All safety decals correctly located and legible. Replace if damaged.
All reective decals and SMV sign correctly located and visible when the disc is in trasport position.
Safety/warning lights correctly installed and working properly.
Paint all parts scratched during shipment or assembly.
All safety lockup devices on the Delta Plow are correctly located.
Use the following checklist after your Delta Plow is completely assembled. Check off each item as it is found
satisfactory or after proper adjustment is made.
The Delta Plow has been thoroughly checked and to the best of my knowledge is ready for delivery to the customer.
(Signature Of Set-Up Person/Dealer Name/Date)
NAME
STREET ADDRESS
CITY, STATE/PROVINCE
ZIP/POSTAL CODE
DELIVERY DATE
MODEL NO.
DEALER NAME
DEALER NO.
SERIAL NO.

4
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
DELIVERY CHECKLIST
Check Delta Plow performance with retail customer/end user.
Review importance of proper maintenance and adherence to all safety precautions with retail customer/
end user.
Check for parts that may need to be adjusted or replaced.
Check all safety decals, reective decals, and SMV sign are correctly located as shown in the Parts Guide and
that decals are legible. Replace if damaged or missing.
Check safety/warning lights areproperly.
Use the following checklist after your Delta Plow is delivered as a reminder of very important information
which should be conveyed to retail customer/end used. Check off each item as it is fully explained.
(Signature Of Set-Up Person/Dealer Name/Date)
Life expectancy of this or any other machine is dependent on regular lubrication as directed in the Owner’s Manual.
All applicable safety precautions.
Along with retail customer/end user, check reective decals and SMV sign are clearly visible with Delta
Plow in transport position and attached to tractor. Check safety/warning lights are in working condition.
Tell retail customer/end user to check federal, state/provincial, and local regulations before towing or
transporting on a road or highway.
Give Owner’s Manul and all Instruction Sheets to retail customer/end user and explain all operating adjustments.
Read warranty to retail customer/end user.
Complete Warranty and Delivery Report form.
To the best of my knowledge, this machine has been delivered ready for eld use and customer has been fully informed
as to proper care and operation.
(Signature Of Set-Up Person/Dealer Name/Date)
AFTER DELIVERY CHECKLIST
The following is a list of items we suggest to check during the first season of use of the equipment.
All registrations must be submitted to:
W&A Manufacturing
PO Box 5238
Pine Blu, AR
All registrations must be submitted to
W&A Manufacturing within 5 business
days of delivery. Retain a copy of this
form for auditing purposes.

5
308.708.8185 | [e-mail] | Rev. 11/20
GENERAL INFORMATION
HOW TO USE THIS MANUAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
WARRANTY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
SIGNAL WORDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
EQUIPMENT SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
SAFETY
SAFETY SIGN LOCATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
SAFETY SIGN CARE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
PREPARATION & SET-UP
POST DELIVERY/SEASONAL/PRE-TILLAGE SET-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
CHECK/CHANGE HITCH CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
HITCHING TRACTOR TO IMPLEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
HYDRAULIC HOSE HOOK-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
LIGHT KIT GUIDE AND RELOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
ELECTRICAL HOOK-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
LEVELING THE IMPLEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
OPERATION
BEFORE FIRST USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
WING LOCK PINS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
FOLDING/UNFOLDING FUNCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
TRANSPORT CHECKLIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
GAUGE WHEEL ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
LEVELING THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
DEPTH SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
SPEED RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
FIELD OPERATION - WING DOWN PRESSURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
OPTIONAL SCRAPER ADJUSTMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARKING/STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
DELTA PLOW™ DO’S AND DON’TS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
TROUBLESHOOTING
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
MAINTENANCE & LUBE
GENERAL MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
MAINTENANCE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BLEEDING FOLD HYDRAULICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
ROW UNITE BOLT TORQUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
HYDRAULIC FITTING IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
PARTS GUIDE
ROW UNIT MOUNTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
LEFT HAND THROW ROW UNIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
RIGHT HAND THROW ROW UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
LEFT HAND THROW ROW UNIT INSIDE MOUNT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
RIGHT HAND THROW ROW UNIT INSIDE MOUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GAUGE WHEEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
SCRAPERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HITCH PINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
TOOLBAR HYDRAULICS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOOLBAR HINGE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
TOOLBAR WING ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LIGHT KIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
This manual is divided into sections. The rst section contains a Table of Contents, General Information,
and a Part Number Index. The remaining sections divide the machine into assemblies and sub-assemblies
which illustrate and list all parts.
W&A Manufacturing parts in this manual are specially designed for this machine and should be replaced
with W&A Manufacturing parts only.
Information in this manual was current at time of printing. However, due to W&A Manufacturing’s
ongoing product improvement, production changes may cause your machine to appear slightly dierent
in detail. W&A Manufacturing reserves the right to change specications or design without notice and
without incurring obligation to install the same on machines previously manufactured.
Right-hand and left-hand as used in this manual are determined by facing the direction the machine will
travel while in use.
HOW TO USE THIS MANUAL
Replacement manuals are available. Call the W&A Manufacturing Main Oce at 308.708.8185, or
download a printable PDF from our website, www.wamfgco.com.
MANUAL REPLACEMENT INFORMATION
When this manual is revised, the modication date is printed on the front cover and on the revised
page(s).
MANUAL REVISIONS
Repaint parts where paint is worn or scratched to prevent rust. Aerosol touch-up paint is available. To
order, call W&A Manufacturing at 308.708.8185.
TOUCH-UP PAINT
Travel
Left Right
Front
Back
GENERAL INFORMATION

8
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
WARRANTY INFORMATION
AGROdeviate LLC (AGROdeviate) warrants each W&A Manufacturing product it manufactures to be
free from defects in material and workmanship for a period not to exceed one (1) year from the date of
sale to the original owner. The warranty is valid provided written notice of the alleged defect is re-
ceived by AGROdeviate during said period and within ten (10) working days after its discovery.
In addition, AGROdeviate warrants each TOOLBAR FRAMEWORK to be free from defects in
material and workmanship for a period not to exceed three (3) years from the date of sale to the
original owner. The warranty is valid providing written notice of the alleged defect is received by
AGROdeviate during said period and within ten (10) working days after its discovery.
This warranty is subject to completion of Product Registration and submission to AGROdeviate.
Warranty applies only if product is installed, operated, and maintained according to product manual
and instructions. Warranty will be void if the product has been subject to misuse, misapplication,
neglect, collision with obstruction, or alteration.
For products, parts, and components NOT manufactured by AGROdeviate, the warranty
obligations of AGROdeviate shall be limited to the Original Equipment Manufacturers’ warranty.
Tires on AGROdeviate equipment are warranted through the respective tire manufacturer and their
network of dealers.
All returns must be pre-approved by AGROdeviate and authorization issued before return. All
returns must include a copy of the original invoice in order to be processed. Any returns without a
copy of the original invoice will not be eligible to receive credit.
If determined that the product is defective in material and/or workmanship, the necessary parts will be
replaced and/or repaired. All warranty repair or labor is to be performed by an AGROdeviate authorized
party. AGROdeviate obligation under this warranty shall be limited to repairing or replacing parts deemed
defective. Warranty does not cover travel expenses. AGROdeviate will bear no other costs including loss,
incurred labor, rental fees, nor other.
All returns shall be pre-paid. If warranty is approved by AGROdeviate, return freight will be credited.
This warranty by AGROdeviate LLC is expressly in lieu of all other warranties, expressed or implied,
including warranty of merchantability and tness for use. We neither assume, nor authorize, any
other entity to accept for us any liability relating to the sale of our products.
INTRODUCTION
Thank you for your purchase of a W&A Manufacturing Delta Plow. Putting your trust in our equipment is something
we don’t take lightly and are humbled that you chose W&A Manufacturing. Having designed all of our equipment with
farmers like you in mind, we hope you enjoy years of productive use from it. Please read and understand this manual before
operation.
GENERAL INFORMATION

9
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
Note the use of signal words DANGER, WARNING, and CAUTION with the
safety messages. The appropriate signal word for each has been selected
using the following guidelines:
SAFETY
TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL YOUR
ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND THE SAFETY OF OTHERS.
FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.
SIGNAL WORDS:
THIS SYMBOL MEANS:
-ATTENTION!
-BECOME ALERT!
-YOUR SAFETY IS INVOLVED!
If you have questions not answered in this manual, require additional copies, or the manual is damaged,
please contact W&A Manufacturing, PO Box 5238, Pine Blu, AR, 308.708.8185, or visit our website:
www.wamfgco.com.
DANGER
WARNING
CAUTION
DANGER: Indicates an imminently hazardous situation that, if not avoided,
will result in death or serious injury. This signal word is to be limited to
the most extreme situations typically for machine components which, for
functional purposes, cannot be guarded.
WARNING: Indicates a potentially hazardous situation that, if not avoided,
could result in death or serious injury, and includes hazards that are
exposed when guards are removed. It may also be used to alert against
unsafe practices.
CAUTION: Indicates a potentially hazardous situation that, if not avoided,
may result in minor or moderate injury. It may also be used to alert against
unsafe practices.
SAFETY

10
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
Safety of the operator is one of the main concerns in designing and developing a new
piece of equipment. Designers and manufacturers build in as many safety features as
possible. However, every year many accidents occur which could have been avoided by
a few seconds of thought and a more careful approach to handling equipment. You, the
operator, can avoid many accidents by observing the following precautions in this section.
To avoid personal injury, study the following precautions and insist those working with
you, or for you, follow them.
In order to provide a better view, certain photographs or illustrations in this manual may
show an assembly with a safety shield removed. However, equipment should never be
operated in this condition. Keep all shields in place. If shield removal becomes necessary
for repairs, replace the shield prior to use.
Replace any CAUTION, WARNING, DANGER or instruction safety decal that is not readable
or is missing. Location of such decals is indicated in this booklet.
Do not attempt to operate this equipment under the inuence of drugs or alcohol.
Review the safety instructions with all users annually.
This equipment is dangerous to children and persons unfamiliar with its operation. The
operator should be a responsible adult familiar with farm machinery and trained in this
equipment’s operations. Do not allow persons to operate or assemble the unit until they
have read this manual and have developed an understanding of the safety precautions
and how it works.
To prevent injury or death, use a tractor with a Rollover Protective Structure (ROPS). Do
not paint over, remove or deface any safety signs or warning decals on your equipment.
Observe all safety signs and practice the instructions on them.
Never exceed the limits of a piece of machinery. If its ability to do a job, or to do so safely,
is in question - DON’T TRY IT.
EQUipment Safety Guidelines
SAFETY... YOU CAN LIVE WITH IT!
SAFETY

12
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
SAFETY SIGN LOCATIONS
These types of Safety Signs and locations on the equipment are shown in the illustrations
below. Good safety requires that you familiarize yourself with the various Safety Signs,
the type of warning and the area, or particular function related to that area, that require
your SAFETY AWARENESS.
461230
461259
461220
461250
461255
461248
461225
461213
NOTE: LH/RH Safety Signs and
locations are similar
SAFETY

13
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
PINCH POINT - WARNING
• Keep extremities clear of equipment. Object(s) can move or shift; can result in
death or serious injury.
• Hazards may include, but are not limited to, hinge mechanism movement, pin movement,
row unit movement and shifting, accessory movement and shifting, etc.
CRUSH HAZARD - WARNING
• Keep clear of moving and shifting equipment. Equipment movement area; will result
in death or serious injury.
• Hazards may include, but are not limited to, connection and disconnection of
equipment, unexpected equipment shifting, etc.
461213
461220
SAFETY

14
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
CRUSH HAZARD - WARNING
• Keep clear of moving and shifting equipment. Equipment can move or shift; can
result in death or serious injury.
• Hazards may include, but are not limited to, folding wing movement, raised equipment
movement and shifting, etc.
NO RIDERS - WARNING
• Never allow riders on equipment; can result in death or serious injury.
• Hazards may include, but are not limited to, falling from equipment, falling into
equipment, injury while on equipment, etc.
461225
461230
SAFETY

15
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
CONTENTS UNDER PRESSURE - WARNING
• Do not operate if damaged or improperly pressurized. Damaged or improperly
pressurized components can discharge; can result in death or serious injury.
• Hazards may include, but are not limited to, damaged tire and/or rim, over pressurized
tire, excessive tire wear, tire tears or punctures, ect.
HIGH PRESSURE FLUID - DANGER
• Use safe practices. Fluid injection can occur; will result in death or serious injury.
• Hazards may include, but are not limited to, injury beyond the entry point, over
pressurized components, damaged components, components with excessive
wear, swollen components, ect.
461248
461250
SAFETY

16
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
ELECTRICAL SHOCK/ELECTROCUTION
HIGH-CLEARANCE DANGER
• Keep clear of overhead power lines, maintain 20-foot minimum distance. Electrical
shock and/or electrocution can occur; will result in death or serious injury.
• Hazards may include, but are not limited to, high clearance equipment, low clearance
power lines, lack of awareness of surroundings, etc.
READ/UNDERSTAND MANUAL - CAUTION
• Do not operate without a complete understanding of the owner’s manual. Do not
operate with unsafe practices; may result in death or injury.
• Hazards may include, but are not limited to, compromising the safety of yourself
and/or others, lack of awareness, damage to equipment, etc.
461255
461259
SAFETY

17
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
SAFETY SIGN CARE
• Keep safety signs clean and legible at all times.
• Replace safety signs that are missing or have become illegible.
• Replaced parts that displayed a safety sign should also display the current sign.
• Safety signs are available from Hawkins Ag.
HOW TO INSTALL SAFETY SIGNS
• Be sure that the installation area is clean and dry.
• Decide on the exact position before you remove the backing paper.
• Remove the smallest portion of the split backing paper.
• Align the decal over the specied area and carefully press the small portion with the
exposed stick backing in place.
• Slowly peel back the remaining paper and carefully smooth the remaining portion of
the decal in place.
• Small air pockets can be pierced with a pin and smoothed out using the piece of decal
backing paper.
REMEBER: If Safety Signs have been damaged, removed, become illegible or parts
replaced without decals, new decals must be applied. New decals are available from
W&A Manufacturing.
W&A Manufacturing
PO Box 5238
Pine Blu, AR 71611
308.708.8185
www.wamfgco.com
SAFETY

19
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
PREPARATION & SET-UP
POSTDELIVERY/SEASONAL SETUP
Read and understand important“Safety”information starting on page 9.
Check that all working parts are moving freely, bolts are tight, and cotter pins are spread.
Check that all grease ttings are in place and lubricated. See“Maintenance & Lube” on page 49.
Check that all safety decals and reectors are correctly located and legible. Replace if damaged. See“Safety
Sign Locations”starting on page 13.
On initial delivery, use with a new tractor, and seasonally check and as necessary, complete these items before
continuing to the routine set-up items:
Bleed hydraulic fold system (page 48)
Check/Change Hitch Conguration
Hitching Tractor to Implement
Hydarulic Hose Hook-up
Light Kit Guide and Relocation
Electrical Hook-up
Leveling the Implement
PRETILLAGE SETUP
Complete this checklist before routine set-up:
This section helps you prepare your tractor and Delta Plow for use. Your must level the implement, hook up
the implement hydraulics to the tractor, and check that the hydraulics have been bled.

20
308.708.8185 | [e-mail] | Rev. 11/20 RETURN TO INDEX
PREPARATION & SET-UP
CHECK/CHANGE HITCH CONFIGURATION
On initial delivery, use with a new tractor, and seasonally check and as necessary, complete these items before
continuing to the routine set-up items:
Choose a hitch option that is compatible with your tractor 3-point. The Delta Plow has two hitch congurations:
Changing between hitch categories requires removing pins at the implement hitch.
TO OPERATE AS CATEGORY 3
1. Remove and store the Category 4 pins
shown below.
2. Once removed, the remaining pins are set
to run the implement with a Category 3
hitch.
• Category 3
• Category 4
**SEE NEXT PAGE FOR CATEGORY 4 HITCH SETUP**