WAGNER FURNO F750 User manual

wagner-group.com
FURNO HEAT GUN
F750 ELECTRONIC LCD
HOT AIR MULTI PURPOSETOOL
OWNER’S MANUAL
Material No. 2366232
Model: 2363345
GB AUS

FURNO 750
3
ENFURNO 750
2
To reduce the risks of re or explosion, electrical
shock and the injury to persons, read and
understand all instructions included in this
manual. Be familiar with the controls and proper
usage of the equipment.
Indicates a hazardous situation which, if not
avoided, could result in death or serious
injury.
HAZARD: POISON
Extreme care should be taken when stripping paint. The peelings,
residue and vapours of paint may contain lead, which is poisonous.
Any paint applied to homes before 1950 is likely to contain lead.
Any paint manufactured before 1977 may contain lead. Once the
paint is deposited on surfaces, hand-to-mouth contact can result in
the ingestion of lead. Exposure to even low levels of lead can cause
irreversible brain and nervous system damage. Young and unborn
children are particularly vulnerable to lead poisoning.
Before beginning any paint removal process you should determine
whether the paint you are removing contains lead. This can be done
by your local health department or by a professional who uses a paint
analyser to check the lead content of the paint to be removed. Lead-
based paint should only be removed by a professional and should not
be removed using a Heat Gun.
PREVENTION:
Move the work piece outdoors, sheltered from rain. If this is not
possible, keep the work area well-ventilated. Open the windows and
put an exhaust fan in one of them. Be sure the fan is moving the air from
inside to outside.
• Remove or cover any carpets, rugs, furniture, clothing, cooking
utensils and air ducts.
• Place drop cloths in the work area to catch any paint chips or
peelings. Wear protective clothing such as extra work shirts, overalls
and hats.
• Work in one room at a time. Furnishings should be removed or
placed in the centre of the room and covered. Work areas should
be sealed o from the rest of the dwelling by sealing doorways with
drop cloths.
• Children, pregnant or potentially pregnant women and nursing
mothers should not be present in the work area until the work is
done and all cleanup is complete.
• Wear an approved dust respirator mask or a dual lter respirator
mask for dust and fumes. These masks and replaceable lters are
readily available at major hardware stores. Be sure that the mask
ts properly. Beards and facial hair may keep masks from sealing
properly. Change the lters often. Disposable paper masks are not
adequate.
• Use caution when operating the Heat Gun. Keep the Heat Gun
moving as excessive heat will generate fumes which can be inhaled
by the operator.
• Keep food and drink out of the work area. Wash hands, arms and face
and rinse mouth before eating or drinking. Do not smoke or chew
gum or tobacco in the work area.
• Clean up all removed paint and dust by wet mopping the oors.
Use a wet cloth to clean all walls, sills and any other surface where
paint dust is clinging. Do not sweep, dry dust or vacuum. Use a high
phosphate detergent of trisodium phosphate (TSP) to wash and mop
areas.
• At the end of each work session, put the paint chips and debris in
a double plastic bag, close it with tape or twist ties and dispose of
properly.
• Remove protective clothing and work shoes in the work area to
avoid carrying dust into the rest of the building. Wash work clothes
separately. Wipe shoes o with a wet rag and then wash it with the
work clothes. Wash hair and body thoroughly with soap and water.
Important Safety Information • Read all safety information before operating the equipment.
Save these instructions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 13
EN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

FURNO 750 FURNO 750
4 5
EN EN
HAZARD: EXPLOSION OR FIRE
This Heat Gun produces extremely high temperatures (as high as
630°C). It must be used with caution to prevent combustible material
from igniting.
PREVENTION:
• Keep the Heat Gun in constant motion. Do not stop or dwell in one
spot.
• Use extreme caution if the
other side of the material
being scraped is inaccessible,
such as house siding. The
hidden side could catch on
re if it becomes too hot.
Some buildings contain highly
ammable materials behind
siding walls, oors, facia, sot
boards and other panels.
Check these areas before applying heat and do not use a heat tool if
ammable materials are present or if you are unsure of the hidden
material.
• Do not use near surfaces with cracks or near metal pipes or ashing.
Heat may be conducted behind the work surface and ignite hidden
material. The ignition of hidden materials may not be readily
apparent and can result in property damage and injury.
• Do not use electric tools in the presence of ammable liquids or
gases.
• Do not use near combustible materials such as dry grass, leaves, and
paper which can scorch and catch re.
• The nozzle becomes very hot. Do not lay the Heat Gun on ammable
surfaces when operating the gun or immediately after switching the
gun o. Always set the gun on a at, level surface so that the nozzle
tip is directed upwards and away from the supporting surface.
• Do not touch the nozzle until the tool has cooled.
• Do not use the Heat Gun as a hair dryer.
• Tools and paint scrapings become very hot. To avoid burns, use work
gloves and eye protection when scraping.
• Always treat the Heat Gun with the same respect as an open ame.
• Do not use in presence of an explosive atmosphere.
HAZARD: ELECTRIC
May cause property damage, severe injury or loss of life.
PREVENTION:
• Do not disassemble the Heat Gun.
• Do not work in wet areas or expose the Heat Gun to rain or moisture.
• Guard against electric shock by preventing body contact with
grounded surfaces such as pipes, radiators, ranges, aluminium
ladders or other grounded devices.
• Do not abuse the cordset. Never carry the Heat Gun by the cordset or
yank on the cordset to disconnect it from the power supply. Keep the
cordset away from heat, oil and sharp edges. Inspect the cordset for
wear or damage regularly.
• If an extension cord is damaged or otherwise unsuitable for use,
replace it with a new extension cord.
HAZARD: GENERAL
May cause property damage or severe injury.
PREVENTION:
• Always disconnect the Heat Gun from the power supply when not in
use. Store indoors in a dry place and out of the reach of unsupervised
children.
• Keep your work area well lit and clean.
• Do not overreach, especially when working on ladders. Keep proper
footing and balance at all times. Be certain any ladders being used are
sturdy, stable, on rm ground and erected at safe working angles.
• Avoid power lines.
• Keep moveable items secured and steady while scraping.
• Always use protective eyewear when working.
• Stay alert and use common sense when operating any tool.
• Never use to thaw frozen pipes located inside walls or near
combustibles. Always use reector nozzle (P/N2366225) to thaw
frozen pipes.
Facia
Soffit
Inside
Wall Siding
• Do not leave the heat gun unattended while it is switched on.
• This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play
with the appliance.
• Keep the appliance and its cord out of reach of children aged less
than 8 years.
MAINS CONNECTION (UK only)
This Heat Gun has been supplied with a fused cordset. This is
identied by the fuse holder in the base of the plug. Please read the
following safety instructions before use:
1. If the cordset is damaged replace with a new cordset to avoid
a safety hazard. Please contact Wagner customer services for a
replacement cordset.
2. NEVER under any circumstances use the Heat Gun or cordset
without the fuse cover tted.This is the little cover xed into the
base of plug to hold the fuse in place.
3. If you lose the fuse cover then please contact any electrical dealer
for a replacement or ring our helpline.
4. A replacement fuse must be rated at 13 Amps. This must be
manufactured and approved to BS1362.
5. IF IN ANY DOUBT PLEASE CONSULT A QUALIFIED ELECTRICIAN.
MAINS CONNECTION (Non-UK)
This Heat Gun has been supplied with a cordset. If the cordset is
damaged replace with a new cordset to avoid a safety hazard. Please
contact Wagner customer services for a replacement cordset.
IF IN ANY DOUBT PLEASE CONSULT A QUALIFIED ELECTRICIAN.
WARNING - Use an extension cord that will accept the plug on the
product. Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized cord will cause
a drop in line voltage resulting in loss of power and overheating. A
harmonised H05RR-F 3x1.0sq mm rubber type cord is required as a
minimum for general use.
Using the Heat Gun
General Description
This Heat Gun is a quality power tool. Like any power tool, it can be
dangerous when misused. Read the following instructions carefully and
follow all safety precautions. It is the responsibility of the owner to use
the Heat Gun properly.
Specications
Housing Engineered high-impact corrosion and heat-
resistant polymers
Wattage 2000 Watts on HIGH, 150 Watts on LOW
Voltage 220 - 240 V a.c.
Frequency 50 - 60Hz
Heat Output Approximately 630°C on HIGH, approximately
60°C on LOW
Weight 0.9 kg

FURNO 750 FURNO 750
6 7
EN EN
Touch Pad Control Panel
The heat gun gives you a wide temperature range to choose from, depending upon the type of project. These can be controlled via the Control Panel.
Temperature Guide LCD Display (Fig. 3)
Description Fig. 3
1) Power button: Turns the heat
gun ON and OFF or switches
the heat tool into cool down
mode
2) Mode selector: Sets the
temperature range and air
ow speed you are using
3) Air ow icon 4) Air ow indicator. Fills from
right to left
5) Text/number display 6) Temperature icon
7) Temperature indicator. Fills
from left to right
8) Temperature selector: Increase
the temperature (+)
9) Temperature selector: Decrease the temperature (-)
Fig. 3
2
1
4 3
5
6 7
9 8
Screen currently shows default start-up display.
300oC at highest fan speed.
Cool Down Mode (Fig. 4)
While the heat gun is operating, press the power button once to
enter cool down mode. When cool down mode is entered, the gun
will run for 30 seconds with maximum air ow. During this period, the
temperature bars will all ash and step down to indicate cooling. To
override cool down mode, press and hold the power button for 2-3s.
Fig. 4
Following Cool down mode the barrel of the gun will
still be hot.
Features Fig. 1
1) Control panel - temperature and fan speed
2) Hanging hook
3) Cordset with integrated stabilizers (removable with tool)
4) Rear stabilizer ns (upright standing)
5) Side bars to prevent nozzle touching surface
6) Nozzle Heat Shield
Fig. 1
5
2
6
3
4
7
1
Removing the barrel cover
The barrel cover can be removed when working in hard to reach
locations. BE CAREFUL OF THE NOZZLE. Increased risk of burning
exists when working without the barrel cover. To remove the barrel
cover, use a small at head scew driver to lift tab (Fig.1, 7) over raised
area.
Attaching the cordset
The cordset (Fig. 2, 1) for the Heat Gun is delivered detached from
the gun (Fig. 2, 2). To attach, line up the cord with the socket on the
handle of the gun and press rmly together until you hear a click. The
cord set does not need to be removed. If required to detach, insert a
small screwdriver or similar tool (Fig. 2, 3) into the hole as shown (Fig.
2, 4). Once resistance is felt on the end of the tool, apply pressure to
depress the release mechanism. Firmly pull the cordset away from the
gun.
Fig. 2
1
2
4
3

FURNO 750 FURNO 750
8 9
EN EN
Start Up
Always read the safety information included in this manual
before using the Heat Gun.
1. Plug the Heat Gun into a standard socket-outlet.
2. Turn on the heat gun by pressing the power button on the
Control Panel (Fig. 3, 1). When the gun is turned on, it is
automatically set t the default temperature of 300oC as shown in
Fig. 3.
3. Use the plus and minus buttons (Fig. 3, #8 & #9) to adjust the
temperature. Single press to increase temperature in ten degree
increments.
4. As the temperature is increased, bars will ash to indicate that
the gun is coming up to temperature. As the higher temperature
is reached, the bars turn solid.
5. As the temperature is decreased, bars will ash to indicate that
the gun is still at a high temperature. As the lower temperature is
reached, the bars turn o.
IMPORTANT: If the blower motor in the heat gun does not turn
on when the POWER button is activated, turn the switch OFF
immediately. The heating element will burn out if it is not cooled
by the blower.
6. During rest periods or when you are nished with your project,
press the power button to enter cool down mode.
7. Set the gun down in an upright position. The heat gun will shut
itself o after 30 seconds.
8. To override cool down mode press and hold the power button
for 2 to 3 seconds. The gun will power o immediately.
Note: Smoke may appear during the rst start up due to the
burning of manufacturing oils. The smoke should disperse
shortly after rst start up.
Hands-free operation Fig. 5
The Heat Gun has an integrated stand (Fig. 1, 4) for bench top
applications and for cooling down. Alternatively the heat gun carry
case (Fig. 6) has been specically designed to locate the heat gun in
the upright position for work on uneven surfaces.
Fig. 5
AngleLoc carry case
The heat gun carry case with
AngleLoc has been specically
designed to locate the heat gun in
the upright position for work on
uneven surfaces.
AngleLoc mount Fig. 6a & 6b
a: Insert the back of the heat gun so that the rear stabilizing ns
locate themselves below the ridges on the side wall of the cavity in
the top of the carry case.
b: Then slide the heat gun forward so that it naturally locks into
place at a 135 degree angle. The heat gun should now be secure for
upright use.
Fig. 6a Fig. 6b
IMPORTANT: If the motor-driven fan in the Heat Gun does not
turn on when the switch is set to either LOW or HIGH, turn the
switch OFF immediately. The heating element will burn out if it is
not cooled by the motor-driven fan.
Note: Always set the Heat Gun upright after it is turned o, either
for a short break or for storage. Avoid laying the unit on the
side after shutdown. The heat will remain in the unit and
cooling will take longer. Store the unit only after the nozzle
is cool. Unplug the unit before storing to prevent accidental
start-up.
IMPORTANT: Always protect glass when working near windows.
Do not touch nozzle or any other tool being used when
working. These become extremely hot and will cause
severe burns. Wear gloves to protect hands from hot
scrapings.
Many variables aect heating applications, such as the material
being heated, ambient temperature, the distance from the gun to
the substrate and the heating technique. For this reason Wagner has
provided temperature guidelines for certain applications. Always start
the heat gun at the lowest temperature in the range then raise the
temperature until the optimum temperature is achieved. Always keep
the heat gun in motion and at least 5cm from the substrate when
applying heat.

FURNO 750 FURNO 750
10 11
EN EN
The FURNO 750 Heat Gun is one of the most versatile tools you can own. It can be used for a great variety of projects, from big DIY to small Art &
Crafts jobs. For more details on multiple projects and ‘how to’ videos please visit our website www.wagner-group.com.
Use Heat Nozzle Tip
Options
DIY Stripping paint HIGH
Concentrator or
Wide
Wall repair LOW Open (no tip)
Drying paint LOW Open (no tip)
Soften adhesives to
remove oor tiles
LOW
Wide
concentrator
Bend plastic, plexiglass,
formica
LOW/HIGH Reector
Nozzle
Removing formica and
linoleum
LOW Wide
concentrator
Soften paint, caulking
and putty for easier
removal
HIGH Concentrator
or Wide
concentrator
Removing varnish LOW-MED Wide
concentrator
Shrink plastic lm
for wrapping or
weatherproong
LOW Wide
concentrator
Small jobs
(including
repair)
Loosen rusted nuts, bolts
and ttings
HIGH Open/
Concentrator
Repairing jeans LOW Wide
concentrator
Burning weeds HIGH Concentrator
Removing adhesives LOW Open (no tip)
Waxing skis/snowboard LOW Wide
concentrator
Glass bre work HIGH Concentrator
or Wide
Use Heat Nozzle Tip
Options
Unfreezing pipes and
locks
LOW Reector
Nozzle
Lighting a bbq grill HIGH Concentrator /
BBQ Nozzle
Heat shrink tubing/
connectors
LOW-MED Reector
Nozzle
Heat concrete prior to
patching
LOW/HIGH Concentrator
Defrosting refrigerator /
freezer
LOW Open (no tip)
Art & Crafts Making candles LOW Open (no tip)
Making soap LOW Open (no tip)
Shrink wrapping
presents
LOW Open (no tip)
Forming foam LOW Open (no tip)
Cookie decoration LOW/HIGH Open (no tip)
Automotive Removing stickers,
emblems and decals
LOW Open (no tip)
Removing dents HIGH Open (no tip)
Removing paint HIGH
Concentrator or
Wide
Applying and removing
window tint
LOW Open (no tip)
Restoring bumpers HIGH Open (no tip)
Electronics Smartphone & tablet
repair
LOW Concentrator
PlayStation and Xbox
repair
LOW Concentrator
Stripping Paint
The Heat Gun heats up the surface and causes the paint to soften, at
which time it can be scraped o easily without damaging the surface.
Some paints may soften even though they do not blister; some may
become rubbery, and some may require higher heat.
When working with several layers of paint, it speeds up the scraping
process to heat the surface thoroughly, all the way to the wood., then
all the layers can be scraped at one time.
A soft wire brush may be the best tool to use for very intricate
surfaces. Mineral paints and nishes, such as cement paint and
porcelain, do not soften with heat, so using a heating tool will not
work for paint removal.
The best method of paint removal
Move the Heat Gun slowly and steadily forward at an angle to the
surface, pointing the nozzle in the direction of motion. This allows you
to scrape safely outside the hot air stream and keeps the scraper and
the scraped surface cooler.
A. Warm air preheats the
surface.
B. Paint is softened by hot air.
A + B. Deep penetration of heat
over total area.
C. Paint can be easily scraped
o as soon as it is softened
and the gun is moved
forward.
D. Stripped surface allowed to
cool.
A B C D
IMPORTANT: The removal of paint by a Heat Gun is safe if the
above guidelines are used, but always keep either a container of
water or an ABC re extinguisher (suitable against Class A, B and
C type res) within reach.
Note: Do not use the Heat Gun on surfaces that can be damaged
by heat, such as vinyl-coated panelling, vinyl-coated siding
or vinyl-coated window frames.
When removing paint from window frames, the Heat Gun
will soften the putty. Be careful not to gouge the putty with
the scraper. The putty will rm up after it cools.
Do not use the Heat Gun on insulating laminated window
glass such as Thermopane. The glass edge expansion may
break the edge seal.
When scraping facia, do not overheat the edges of the
asphalt shingles protruding over the edge of the sheathing.
Too much heat will melt the asphalt.
Cleaning and Maintenance
Keep the intake openings on the housing clean and free of
obstructions. Use a soft, dry brush to clean the openings periodically.
Use only mild soap and a damp cloth to clean the Heat Gun. Many
household cleaners contain chemicals which could seriously damage
the housing.
Do not use petroleum, turpentine, lacquer or paint thinner, dry
cleaning uids or similar products when cleaning the Heat Gun.
NEVER allow any liquid to get inside the tool or immerse any part of
the tool into a liquid.
Cleaning and user maintenance shall not be made by children unless
they are older than 8 years and supervised.
Storage
Allow the Heat Gun nozzle to cool to room temperature before
placing in storage.
The nozzle will turn dark over time because of the high heat. This is
normal and will not aect the performance or life of the unit.

FURNO 750 FURNO 750
12 13
EN EN
Accessories
The following accessories may come with the Heat Gun or may be purchased separately by visiting www.wagner-group.com/service.
Alternatively see back of manual for your nearest Service Centre.
Name Description Name Description
Concentrator
Nozzle
P/N2366222
Directs a concentrated heat
ow to the work surface. Ideal
for removing paint in awkward
corners, crevices, mouldings,
beading or architraves.
Glass Protection
Nozzle
P/N2366224
Deects the heat away from
glass or other fragile areas. Ideal
for window sills, ledges, frames
and skirting boards.
Wide Concentrator
Nozzle
P/N2366223
Directs a long, narrow heat pattern
to the work surface. Ideal for
removing paint or varnish from
large, at surfaces such as skirting
boards, doors, stairs, etc. It should
be used in conjunction with a at
scraper.
Reector Nozzle
P/N2366225
Disperses the heat ow evenly
around the whole work surface.
Ideal for thawing frozen pipes,
solder pipe work, bending
plastics or heat shrinking
electrical insulating tubing.
Name Description
5-in-1 Detailed
Scraper Tool
P/N2366227
1+2 4
3
5This tool has 5 functions. The blade is used to (1) scrape paint and (2) spread
compound. The gouge point (3) is used to remove putty/caulk from open
cracks. The curved area (4) is used to clean roller covers. The at side (5) can be
used to open paint tins.
Carry Case
P/N2366226
The heat gun carry case with AngleLoc has been specically designed to
locate the heat gun in the upright position for work on uneven surfaces.
Product Registration
Register your product online at www.wagner-group.com/3plus1 to
qualify for your additional 1 year guarantee.
3+1 years guarantee
The guarantee runs for three years, counting from the date of sale
(sales slip). The guarantee is extended by a further 12 months if
the device is registered online within 4 weeks of the purchase at
www.wagner-group.com/3plus1. Registration is only possible if the
buyer is in agreement with the data being stored that is entered during
registration. The guarantee covers and is restricted to free-of-charge
rectication of faults which are demonstrably attributable to the use of
faulty materials in manufacture, or assembly errors; or free-of-charge
replacement of the defective parts. The guarantee does not cover
incorrect use or commissioning or tting or repair work which is not
stated in our operating instructions. Wearing parts are also excluded
from the guarantee. The guarantee excludes commercial use. We
expressly reserve the right to full the guarantee. The guarantee expires
if the tool is opened up by persons other than wagner service personnel.
Transport damage, maintenance work and loss and damage due to
faulty maintenance work are not covered by the guarantee. Under any
guarantee claim, there must be proof of purchase of the tool through
submission of the original receipt. Wherever legally possible, we exclude
all liability for injury, damage or consequential loss, especially if the tool
has been used for a purpose other than that stated in the operating
instructions, commissioned or repaired other than in accordance with
our operating instructions or if repairs are performed by someone who
is unqualied. We reserve the right to perform any repairs in excess of
those stated in our operating instructions. In case of guarantee or repair,
please refer to your point of sale. This guarantee does not aect your
statutory rights.
INFORMATION ON THE DISPOSAL OF WASTE ELECTRICAL AND
ELECTRONIC EQUIPMENT KNOWN AS WEEE
Your attention is brought to new directives applicable to
the disposal of this electrical equipment where, in
accordance with legislation, this product must not be
disposed of in your normal household waste. Instead it is
your responsibility to dispose of this type of waste by
handing it over to special designated collection points for
recovery and recycling. This product is marked with a
‘Wheelie bin’ symbol with a cross on it to remind you of this action. The
objective of this directive is to help conserve resources and ensure that
it is recycled in a manner that protects human health and the
environment. For more information about where you can drop o your
waste please contact your local authority, take back facilities are free of
charge.
CE Declaration of Conformity
This product complies with the Low Voltage Directive 2014/35/EU,
EMC Directive 2014/30/EU, RoHS Directive 2011/65/EU and REACH
Regulation 1907/2006.

FURNO 750 FURNO 750
14 15

J. WAGNER GMBH
Otto-Lilienthal-Str. 18
D-88677 Markdorf
T +49 0180 - 5592 4637
F [phone]
DE
WAGNER FRANCE S.A.R.L.
12 Avenue des Tropiques
Z.A. de Courtaboeuf
F-91978 Les Ulis Cedex
T [phone]
F [phone]
FR
ORKLA HOUSE CARE DANMARK A/S
Stationsvej 13
3550 Slangerup
DK-Danmark
T [phone]
F [phone]
DK
MAKIMPORT
HERRAMIENTAS, S.L.
C/ Méjico nº 6
Pol. El Descubrimiento
E-28806 Alcalá de Henares
(Madrid)
T 902 199 021 / 91 879 72 00
F 91 883 19 59
ES
PT
J. WAGNER AG
Industriestraße 22
CH-9450 Altstätten
T [phone]
F [phone]
CH
WAGNER SPRAYTECH
AUSTRALIA PTY. LTD.,
14-16 Kevlar Close
AUS-Braeside, VIC 3195
T [phone]
F [phone]
AU
PUT WAGNER SERVICE
ul. E. Imieli 27
PL-41-605 Swietochlowice
T [phone]
F [phone]
PL
WAGNER SPRAYTECH (UK) LTD
Opus Park
Moorfield Road
Guildford, Surrey, GU1 1SZ
T [phone]
F [phone]
GB
E-CORECO SK S.R.O.
Kráľovská ulica 8/7133
SK-927 01 Šaľa
T [phone]
F [phone]
SK
SE
ORKLA HOUSE CARE AB
Box 133
564 23 Bankeryd
SV-Sweden
T [phone]
ROMIB S.R.L.
str. Poligonului nr. 5 - 7
ROM-100070 Ploiesti ,judet Prahova
T [phone]
F [phone]
RO
ORKLA HOUSE CARE NORGE AS
Nedre Skøyen vei 26,
PO Box 423, Skøyen
N-0213 Oslo
T [phone]
NO
E-CORECO S.R.O.
Na Roudné 102
CZ-301 00 Plzeň
T [phone]
F [phone]
CZ
HONDIMPEX KFT.
Kossuth L. u. 48-50
H-8060 Mór
T +36 (-22)-407 321
F +36 (-22)-407 852
HU
Material No. 2366232
06/2016
© Copyright by J.Wagner GmbH
Irrtümer und Änderungen vorbehalten.
Not responsible for errors and changes.
Sous réserves d’erreurs et de modifications.
Fouten en wijzigingen voorbehouden.