Walker Edison BQSPIN User manual

BQSPIN
P.1
Assembly Instructions
Revised 0 /2011 9
2018

P.2

1
13
13
14 1
5
5
9
6
7
12 10
12
8
3
3
12
12
11
3
4
1
222222222222
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
P.3
Part 1: Spindle
Part 2: Slat
Part 3: Legs
Part 4: Cross bar
Part 5: Bracket
Part 6: Top rail
Part 7: Bottom rail
Part 8: Front rail
Part 9: Back rail
Part 10: Right side rail
Part 11: Left side rail
Part 12: Feet
Part 13: Support beam
Part 14: Spindle Support Rail (For assembly use only)

P.4
Hardware List
L
M
N
Hex key
Wrench
Spacer
02 pcs
01 pcs
02 pcs
1/4"x60 mm
Washer
Bolt
Nut
05 pcs
05 pcs
05 pcs
I
K
J
7x70 mm
7x50 mm
Bolt Black
Black
Black
Black
Black
Black
Bolt
13 pcs
8 pcs
A
D
B3.5x30 mm Screw 52 pcs
C3.5x30 mm Screw 42 pcs
F
G
H
E
10x40 mm
10x30 mm
6x30 mm
10x50 mm
Wood dowel
Wood dowel
Wood dowel
Wood dowel
06 pcs
02 pcs
04 pcs
08 pcs
Screw
O04 pcs
Ø1/4"X50mm
Union Screw
P04 pcs
Ø1/4 "

Insert wooden dowels (E) into rails (8,9), dowels (F) into parts (4,5) and dowels (H) into parts (13)
Attach legs (3) to cross bar (4) using bolt (A) and hex key (L)
F
F
Step 1
Step 2
P.5
E
E
E
E
E
E
E
E
4
8
9
2X
2X
F
F
5
H
H
13
A
A
A
L
L
L
4
3
3
3

A
A
A
L
Secure part (4) to part (8,9) using bolt (A) and hex key (L)
Step 4
Step 3
8
3
34
8
9
11
10
9
L
L
A
P.6
Connect parts (10,11) to parts (8,9)

Step 05
Step 06
A
A
A
A
A
A
A
A
L
L
L
L
L
L
L
11
10
9
8
P
P
P
P
D
O
D
O
O
DD
D
LL
L
L
L
L
L
L
L
O
8
11
9
10
P.7
Aach legs (12) to frame parts (10,11) using screw (O) and Union Screw (P). Union Screw (P) should be on the inside
of the bed frame, with screw (O) on the outside of the leg. Tighten by using with hex key (L) on both ends of the screw
at the same me. Then use screw (D) and hex key (L) to secure legs (12).
Secure parts (10,11) to parts (8,9) with Screw (A).
12
12
12
12
12

C
C
CC
C
C
C
C
C
C
C
C
C
CC
C
C
C
Step 07
Step 08
12
12
12
12
12
11
10
9
8
Secure feet to frame using screw (C). Secure parts (10, 11) to parts (9,8) using screw (C)
P.8
C
C
7
7
5
5
5
5
Connect parts 5 to part 7. Note the drawing for location of pocket hole. Secure parts (5) to part (7)
using screw (C).

Step 09
Step 10
P.9
C
C
C
C
C
C
C
C
C
C
13
13
1 14x
C
C
C
C
Attach parts (13) to part (6) using bolt (D) and hex key (L)
Attach spindles (1) to part (6) using screw (C). Pocket holes and screws (C) should be positioned to
face away from part (13). To ensure that screws are on the back of the hardboard when assembly is
complete. Note- apply downward pressure to each spindle while attaching to part (6) to ensure an
even & secure fit.
13
13
6
6
D
D
D
L
L
L
13
6

Step 11
Step 12
C
C
6
6
13
13
13
1
5
7
6
13
14
DL
6
13
14
C
Start at one end of the headboard. Fit large spindle (13) into part (5) and secure with screw (D) and
hex key (L). Attach first spindle (1) to first hole in part (7) with screw (C). NOTE- Be sure to align the
first 3 spindles into the correct holes before tightening the first spindle.
7
1
5
5
13
DL
DL
P.10
Place the spindle support rail (14) under the spindles (1) to help align each spindle into the correct
hole in part (7).
Fit the wood dowel from large spindle (13) into part (5).