wallas 3008 User manual

3
2
4
5
6
7
1
1
2
3
6
7
5
44
Combi Thermostatic Mode: Set a target cabin tempe-
rature (C°/F°) for heating.
Ventilation Mode: Blow fresh air without heating.
SET OPERATION MODE
Prior to starting the heater, choose mode by using
the Arrow Buttons (left or right) to move the
orange selection square to the Main Menu Bar,
press Select Button to activate the Main Menu Bar,
use Arrow Buttons to choose the desired mode and
press the Select Button to select. To switch
between modes, turn the heater off and start in the
desired mode.
To start, use the Arrow Buttons
(left or right) to move the orange
selection square to the white
Start/Stop Icon and press the
Select Button. Confirm the
selection by holding the Select
Button down for 3 seconds (safety
feature). White icon turns orange.
Starting will appear on the screen.
The light orange combustion light
will light up when the burner flame
has been ignited and the
combustion has stabilized (in about
5 min). Heater will be fully
operational about 10 min later.
IGNITION
In Combi Thermostatic Mode,
move the selection square to the
Target Temperature and press the
Select Button. Press Arrow
Buttons (left or right) to set the
desired target temperature.
3 0 0 8 A D V A N C E D C O N T R O L P A N E L
Main Menu Bar
Combi Thermostatic Mode
Ventilation Mode
Settings
Temp Sensor
Device Info
Device Stats
Clear Lock
Temp Unit (C°/F°)
Connections
Altitude
CABIN TEMPERATURE CONTROL
Power On/Off
Combustion
Info
Lock
Heater power %
Select
Button
Left Arrow
Move cursor
left or up
Right Arrow
Move cursor
right or down
Digital Panel Legend
OPERATION GUIDE
V i k i n g C o m b i
Please Refer to Manual for Full Operation and Maintenance Instructions at wallas.com
WATER TEMPERATURE
Viking Combi is primarily an air heater - water is heated simulta-
neously as a convenient by-product. Power distribution is approxi-
mately 50-90 % for air heating and 10-40 % for water heating.
Water temperature cannot be controlled separately.
Target Temperature / Blower
Speed
Room / Water Temperature
Heater Status
Start/Stop Icon
Air Boost Icon
Info Bar
(IN THERMOSTATIC MODE)

AIR BOOST
Use Arrow Buttons
to move the selector
to the Air Boost icon
and press the Select
Button.
The orange Air Boost
On icon will appear.
Ventilation Mode blows fresh air without
heating with six blower speeds. Choose
Ventilation Mode prior to starting the heater.
VENTILATION MODE
Pause Mode automatically turns the heater off if the
temperature remains +2 C (3 F) above the set level
for 1/2 hour due to local ambient conditions.
Pause Mode can be turned off temporarily by slightly
increasing the target temperature.
PAUSE MODE
If the heater is in Pause Mode,
Paused and a Pause Icon will appear
on the screen.
Heater will re-start heating again
automatically, if the cabin
temperature falls 2 degrees C (3 F)
below the set target temperature.
Air Boost feature maximizes the air volume for quick
defrosting and drying, but does not change the set
temperature. Air Boost can be activated in Combi
Thermostatic Mode.
To go back to normal
air volume, choose
the Air Boost icon
again and press the
Select Button. The
Air Boost icon will
change back to white.
Use the Arrow Buttons to move
the selection square to the Main
Menu Bar and press the Select
Button to activate it.
Use Arrow Buttons to choose
Ventilation Mode and press the
Select Button.
(IN THERMOSTATIC MODE)
If a Lock Icon is displayed, the
heater has locked itself for safety.
The heater will also lock after 2
unsuccessful starts. Move the
selection square to the
Exclamation Point Icon and press
the Select Button. An Error Page
will appear.
LOCK
If the heater has locked itself,
there may have been a failure
that should be investigated and
resolved prior to further use. The
error page will display a check list
and a website for further
information. If you need help,
reach out to a professional.
(SAFETY FEATURE)
Press and hold the Select Button
down for more than 4 seconds.
Stopping will appear and the
Power Icon light will change to
white indicating the unit is off.
SHUTDOWN
Note: The system mode that was used last upon
shutdown will be the same mode when the heater
is turned on again. To remove the lock, press any
button to return to the main display.
Move the selection square to the
Main Menu Bar and press the
Select Button, choose Settings, and
press the Select Button. Choose
Clear Lock from the Settings Menu
and press the Select Button.
Select
Button
All rights reserved. Wallas-Marin reserves the right to change or improve its products and to make changes in the content of this guide
without obligation to notify any person or organization of such changes or improvements. Go to www.wallas.com for current updates and
supplemental information concerning the use of this product.
Move the selection square to the
Start/Stop Icon and press the
Select Button once. Press the
Select Button down again for 3
seconds to confirm (long press)
and start the heater. Yellow
Power On light will appear in the
Info Bar.
Choose the blower speed
(1-6) by moving the selection
square to the Blower Speed and
press Select Button to activate
the field.
Press Arrow Buttons to set the
desired power and press the
Select Button to choose.
To deactivate ventilation, turn
the heater off. Re-start in the
desired mode.