wallas PI Thermo User manual

Press the Power Button for 3 seconds until
the yellow power light will come on. When
you release the button, the yellow heating
light will appear.
COOKING
Red combustion light will light up when the
burner flame has been ignited and the
combustion has stabilised (approx. in 5 min).
Stove will be fully operational about 10 min
later.
I
P I T H E R M O C O N T R O L P A N E L
When Manual Mode for cooking is
on, the orange Thermostat light is off.
IGNITION
Combustion indicator
Temperature / Power knob
Power button
Power indicator
Thermostat/blower lid indicator
Thermostat sensor
Heating indicator
1.
2.
3.
4.
5.
6.
7.
In Manual Mode, turn the Temperature/
Power Knob to max. level 6 and begin
cooking. Adjust it to a lower temperature,
if needed, as you would a domestic stove.
Stove is set to always start in Manual
Mode ready for cooking.
OPERATION GUIDE
S t o v e s 8 0 0 D S L , 8 5 D T / N D T , 8 8 D U , X C D u o
Please Refer to Manual for Full Operation and Maintenance Instructions at wallas.com
1: ~ 5 °C (~ 41 °F)
2: ~ 11 °C (~ 52 °F)
3: ~ 17 °C (~ 63 °F)
4: ~ 23 °C (~ 73 °F)
5: ~ 29 °C (~ 84 °F)
6: ~ 35 °C (~ 95 °F)
123
4
56
7
Temperature Chart for
the thermostat in
heater in PI Thermo
Mode for stoves with
heater blower lid:
HEATING WITH BLOWER LID (STOVES WITH BLOWER LID)
Once the stove is fully ignited, lower the blower lid down
until it locks and the device will begin to blow warm air
for cabin heating.
When the PI Thermo Mode is chosen,
the orange thermostat/blower lid light
is on.
Rotate the Temperature/Power Knob to the
desired temperature in PI Thermo Mode
(refer to temperature chart above) or control
heating power with knob in Manual Mode.
Switch between modes by turning the
Temperature/Power Knob back and
forth to min - max - min.
To switch back to cooking, unlock the lid and push
it back to upward position. Make sure the stove is
in Manual Mode before cooking.
Stove does not operate correctly if it is left in
PI Thermo Mode.
In Manual Mode, the light is off.
PI Thermo Mode: Set a target temperature (C°/F°)
Manual Mode: Control heating power with knob
SHUTDOWN
I
Press the Power Button down for 2
seconds. Yellow heating light will shut off
immediately.
Red combustion light will continue to
flash for about 5 minutes, while the stove
is cooling down. Unit cannot be restarted
until the cool down is completed.

Heating on
30 s 30 s
Combustion has begun/is running
Set temperature on heater is higher than
cabin temperature - power is increasing
Set temperature on heater is lower than
cabin temperature - power is decreasing
Locked for security
The device locks itself
after two unsuccessful starts
Sun Switch has shut down the device
Cooldown/Flameout
I
Heating on in High Altitude Mode
I
Overheat
I
Reminder indicating there was a fault
after fault code flashed for 5 min
30 s
www.wallas.com
If the unit has locked itself,
the combustion light (1) and
the heating indicator light (7)
will flash signaling there has
been a failure that should be
investigated and resolved
prior to further use. Lights
will flash for about 5 min.
1) While the lights are still
flashing, switch the main
power off from the battery
(Pull power plug, remove the
fuse, open breakers, or in-line
switch).
2) Wait for 5 sec. and switch
the main power back on.
3) Press Power Button (3) for
more than 3 seconds to shut
down the unit.
4) Restart the unit normally.
UNLOCKING THE
UNIT
Reach Out to a Wallas Professional for the Following:
Glow Failure
2 s 2 s
Combustion Air Blower Fault
2 s
Main Blower Fault
2 s
2 s
I
I
I
Low voltage (usually about 15 sec
after initiating start)
I
See instructional video
to unlock
All rights reserved. Wallas-Marin reserves the right to change or improve its products and to
make changes in the content of this guide without obligation to notify any person or organization
of such changes or improvements. Go to www.wallas.com for current updates and supplemental
information concerning the use of this product.
PANEL LIGHTS
I
Sun Switch automatically turns the heater blower
lid off if the room temperature remains +3 C (37 F)
above the set level for 1/2 hour due to
temperature increase in local ambient conditions.
SUN SWITCH (IN PI THERMO MODE)
Orange thermostat light will
begin to flash every 30 seconds.
Turn the Power Knob slightly to
turn the Sun Switch off
temporarily.
If heating is still needed, turn
the device back on manually.
see
ignition
When the device is used 1500 m (4,900 ft)
above sea level, it is necessary to activate the
High Altitude Mode to adjust the combustion.
I
I
HIGH ALTITUDE MODE
Start the stove by holding the
Power Button down for 10
seconds.
Yellow heating light will flash 3
times and then change to a solid
yellow light. High Altitude Mode is
now on and the stove has started
the ignition process.