WALTERSCHEID CONNECTED SERVICE COUNTER User manual

CONNECTED SERVICE COUNTER
Assembly instruction
Installation instruction
MANUAL
www.walterscheid.app
ASaDS2301.1
09-11-2023

GB
2
Required tools
• Pencil
• Ø3 mm metal drill bit
• Ø8 mm metal drill
• Cordless screwdriver
• Phillips screwdriver
• Coin
• Clamp
Scope of delivery
1 1x Counter
2 1x Mounting element
3 2x Screws
4 1x Battery CR2032
5 1x Operators manual

GB
3
1 Assembly instruction
Requirements for Assembly
The drive shaft must meet the following requirements:
• The guard tube and the entire protective equipment of the drive
shaft is complete and undamaged,
• The guard tube is secured against rotation,
• Use only on WALTERSCHEID drive shafts
Assembly instruction

GB
4
1.1 Determination of the position on the PTO shaft guard
The selection of the appropriate position for the Counter is made on
the machine with the PTO shaft installed. Select a position on the outer
guard tube of the PTO shaft that meets the following criteria:
• The Counter should be positioned on the outer protective
tube near the guard cone.
• No labeling on the PTO shaft guard should be obscured.
• A collision with the holding device (support) must be avoi-
ded.
• Contact with hydraulic hoses or chains must be avoided.
Assembly instruction

GB
5
1.2 Marking the position on the PTO shaft guard
Please mark the selected position for later assembly with a suitable pen.
For non-round guard tubes, select a position that is as fl at as possible
on the circumference of the guard tube (see illustration on the right).
Assembly instruction

GB
6
1.3 Disassembly of drive shaft and shaft guard
To prevent damage to the PTO shaft during installation, the outer part
of the shaft guard must be removed from the PTO shaft. Disassemble
the PTO shaft and the shaft guard according to the manufacturer‘s
instructions.
https://www.walterscheid.com/en/downloads/manuals/
Assembly instruction

GB
7
1.4 Fixing the PTO shaft guard
Fix the disassembled shaft guard in a clamp. Fix the protective half
in such a way that the mounting position for the counter can be easily
reached and the guard tube is not damaged.
Assembly instruction

GB
8
1.5 Place and fi x Counter
Fix the Counter at the previously marked position to use it as a drilling
template. Then pre-drill the two holes with a Ø3 mm metal drill bit.
Assembly instruction

GB
9
1.6 Drill holes
Remove the counter from the protective half and then drill out the two
Ø3 mm holes with a Ø8 mm metal drill bit. Then remove chips and burrs.
Assembly instruction

GB
10
1.7 Hook mounting element
Insert the mounting element into the holes by hooking the metal hooks
into the holes one after the other.
1.7
Hook mounting element
Assembly instruction

GB
11
1.8 Mounting of Counter
Carefully place the Counter on the mounting element. The metal hooks
of the mounting element must be inserted into the bottom of the Counter
housing.
Assembly instruction

GB
12
1.9 Mounting of Counter
Carefully insert the screws into the Counter and tighten them with the
Phillips screwdriver (tightening torque ~0.8 Nm).
The tight fi t of the screws and the counter on the shaft guard must be
checked regularly.
Assembly instruction

GB
13
1.10 Assemble PTO shaft
After you have checked the tight fi t of the Counter, you can mount the
shaft guard on the PTO shaft according to the manufacturer‘s inst-
ructions and then reinstall it on the machine. For the activation of the
counter install the Walterscheid Connected Service App and follow the
further instruction under „Add Counter“.
Download WCS Assistant App:
https://www.walterscheid.app
Assembly instruction

GB
14
2 Installation instruction
2.1 Open battery cover
Open the Counter by using a coin to turn the cover 90° counter¬clock-
wise to the open position. Now you can open the cover upwards.
Installation instruction

GB
15
2.2 Scan data matrix code with WCS Assistant
Open the Walterscheid Connected Service app on your smartphone and
click on „Add counter“ on the home screen. In the next step, you will be
asked to scan the data matrix code on the circuit board of the Counter.
Installation instruction

GB
16
2.3 Insert battery
Insert the battery into the battery cover. Make sure that the plus pole of
the battery points to the plus symbol in the battery cover.
Installation instruction

GB
17
2.4 Close battery cover
Press the lid in the open position (lock symbol) onto the lower part of the
housing. You can then use a coin to close the battery cover by turning
it 90° clockwise.
Installation instruction

Off-Highway Powertrain Services Germany GmbH
Hauptstraße 150
D-53797 Lohmar
Tel: [phone]
Fax: [phone]
E-Mail: [email protected]
www.walterscheid.app
Off -Highway Powertrain Services Germany GmbH reser-
ves the right to make technical modifi cations without
prior notice.
ASaDS2301.1
09-11-2023