Warmup + Kit User manual

Kit
Installation Guide
+

Contents
2
Components ....................................................
Step 1 - Download the MyHeating App .....................
Step 2 - Install the Boiler Receiver ........................
Step 3 - Mounting..............................................
Step 4 - Pairing the 4iE to the Boiler Receiver............
Step 5 - LED Indications ......................................
Step 6 - Control in event of communication error .......
Step 7 - Address setting ......................................
Troubleshooting ...............................................
Technical Specications.......................................
3
5
7
12
15
17
18
19
22
23

Kit for use with the 4iE
Components
Power Base Stand Boiler Receiver
Power Adapter with 1m
USB Cable
3
+

Kit
Step 1 - Download the MyHeating App
+

The MyHeating app is available for iOS and Android devices via the App Store or Google Play. If
you have not done so already, download the MyHeating app to your tablet or smartphone.
Registration
After the app has been successfully downloaded you will need to set up your MyWarmup
account. The 4iE Device can be registered via the app or by visiting my.warmup.com
Kit for use with the 4iE
Step 1 - Download the MyHeating App
5
+

Kit
Step 2 - Install the Boiler Receiver
+

Kit for use with the 4iE
Step 2 - Install the Boiler Receiver (Electrician Required)
Before making any permanent xtures Warmup recommends progressing through to ‘Step 4 -
Pairing the 4iE & Boiler Receiver’upon identifying preferred locations for the Boiler Receiver
and Power Base. This will ensure the wireless connection is not subject to range or interference
issues once installed.
IMPORTANT INFORMATION: Installation of the Boiler Receiver should only be carried out by a
qualied electrician. It requires a permanent 230V supply.
The Boiler Receiver should be connected to the central heating fused spur or circuit breaker in
accordance with current wiring regulations such that there is a single point of isolation for all
interconnected devices.
Ensure that multi stranded wires are fully inserted into the terminals and secured tightly. Any
loose strands should be trimmed as they could cause a short-circuit.
This product uses mains voltage electricity and work should only
be carried out by a qualied electrician. Electrical installation
to be in accordance with latest edition of BS7671 Wiring
Regulations and appropriate Statutory Regulations.
!
7
+

Kit for use with the 4iE
Step 2 - Install the Boiler Receiver (Electrician Required)
The Boiler Receiver should be installed in the boilers vicinity. Large metal objects such as the
boiler, hot water cylinder or radiators, should be at least 300mm away from the Boiler Receiver
and not directly between it and the 4iE.
Loosen both screws at
the bottom of the Boiler
Receiver and remove
the backplate.
Fix the backplate to the
wall using xing screws
provided.
Make sure to avoid cables or pipes
which may be buried in the wall
!
8
+
1 2

Kit for use with the 4iE
Step 2 - Install the Boiler Receiver (Electrician Required)
Wiring Diagrams
9
+
1 2 3 4
3

Kit for use with the 4iE
Step 2 - Install the Boiler Receiver (Electrician Required)
After the Boiler Receiver has been wired correctly reattach the front panel to the back plate
and tighten both screws to secure.
Restore power to the
boiler. The LED on the
Boiler Receiver will ash
RED which means it has
to be paired to the Power
Base.
4
10
+
4

Kit
Step 3 - Assembly
+

Kit for use with the 4iE
Step 3 - Mounting
12
Remove the 4iE from its
packaging. Loosen both
closing screws located
at the bottom of the
4iE. Separate the front
housing from the back
plate.
Thread the power cable
through the Stand and
connect to the Power
Base from your +Kit.
Clip the Power Base
onto the Stand. Connect
the plug to a wall socket.
For optimal performance the thermostat should be located in an area with good ventilation. It
should not be beside a drafty window/door, in direct sunlight or above another heat generating
device (e.g. radiator or TV).
12
For Stand Mount
+

Kit for use with the 4iE
Step 3 - Mounting
Remove the 4iE from its
packaging. Loosen both
closing screws located
at the bottom of the 4iE
Separate the front
housing from the back
plate.
Drill a hole in the wall
to feed the USB Cable
to your wall socket. Attach
the Power Base from your
+Kit to the wall using the
xing screws provided.
Connect the plug to the
wall socket.
For optimal performance the thermostat should be located in an area with good ventilation. It
should not be beside a drafty window/door, in direct sunlight or above another heat generating
device (e.g. radiator or TV).
13
For Wall Mount
+
12
NOTE: For detailed instructions, see online at www.warmupsmart.com/installation

Kit
Setup
+

15
Kit for use with the 4iE
Step 4 - Pairing the 4iE & Boiler Receiver
+
The LED on the Boiler
Receiver will stop
ashing RED to indicate
a successful connection.
Using a device, such as a
paper clip, press the
pairing button, as shown
above, on the Power
Base to begin pairing.
2
Power
button
LED
Pairing Button
3
Attach the 4iE front
face to the Power
Base and tighten both
closing screws.
Before pairing, please make sure the Power Base and Boiler Receiver are powered. The LED on
the Boiler Receiver will ash in RED slowly.
NOTE: If the devices have been paired before, hold the Power button on the Boiler Receiver for 6 seconds
and then continue set up.
1 2 3

Kit for use with the 4iE
Step 4 - Pairing the 4iE & Boiler Receiver
16
+
To check that the system
has been installed
successfully, increase the
air temperature by
setting a temporary
override.
Once the 4iE has
powered up, connect to
your WiFi Network.
The heating indicator
will appear on the 4iE,
the light on the Boiler
Receiver will turn solid
GREEN and your heat
system should now
activate.
overrideWi-Fi
target
Warmup until
backback acceptaccept
21.0°C 15min
4 5 6

Kit for use with the 4iE
Step 5 - LED Indications
17
+
LED Colour LED Status Meaning
N/A Not lit Paired
Green Lit constantly Relay on
Red Flashing slowly Not paired
Red Flashing quickly Relay o
Red Lit constantly Communication Lost
Relay on
LED
LED Status

Kit for use with the 4iE
Step 6 - Control in event of communications error
18
+
The Warmup +Kit for use with the 4iE has been designed to still provide heating control should
the communication between the Power Base and Boiler Receiver be interrupted.
With the Power Base and Boiler Receiver paired and the thermostat calling for heat, the relay
will be activated and the Boiler Receiver will show a constant green LED indication. If the
communication between the Power Base and Boiler Receiver is lost, the green LED will remain
on the Boiler Receiver for a period of up to 30 minutes.
If communication has not been restored after 30 minutes has expired, the Boiler Receiver will
indicate a communications fault by displaying a red LED ashing quickly.
To activate the relay whilst communication has been lost, press the power button on the Boiler
Receiver once. The LED indicator will change from a constant to quick ashing red.
To de-activate the relay whilst communication has been lost, press the power button on the
Boiler Receiver once. The LED indicator with change from constant red to ashing quickly red.
Once communication has been restored, the LED indicator will change back to constant green
providing the thermostat is calling for heat.

Kit for use with the 4iE
Step 7 - Address setting
19
+Address Set-up
When using multiple +Kit’s, each Power Base should be set to a unique address to prevent
interference. Use the dip switches on the Power Base to select the unique address. 1
Represents ON (up) and 0 represents OFF (down).
Dip Switches
Address 31
Address 61
Address 53
Address 62

Kit for use with the 4iE
Step 7 - Address setting
+Address Set-up
20