Warmup W3115DT AU User manual

Dual Touch
Thermostats
W3115DT & W3115DT Black

Menu Structure
Time
Day
Mode
A/F/AF mode
Period display
Power Button
Menu button
Confirm button
Setting function
Temperature
Preset temperature
Arrow keys
Return button
Points to note:
To turn off the heating
Tap the power button once to turn off the heating; the towel rail will remain ON
To turn off both –the underfloor heating and the towel rail
Press and hold the power button for 3 seconds
Read the Electrical Requirements supplied with the thermostat. This thermostat uses an
electronic off so it can only be used for functional (control) switching. It cannot be used as
an isolation switch. The power supply needs to be on RCD protection and needs a separate
isolation switch for the supply.
The towel rail is programmed to remain on for 3 hours (by default). You can change this to 1
or 2 hours by pressing and holding the menu button for 3 secs till a number pops up. Scroll
down to 24, press tick and set the minutes to 60 (1 hour) or 120 (2 hours).

Startup Wizard
1. Press 5 times to select Time and press
to confirm.
2. Use the top and down arrow keys to
i. Set the hour then press to confirm
ii. Set the minutes, press to confirm
3. Press to exit
1. Press 4 times to select Date and press to
confirm.
2. Use the up and down arrow keys to
i. Set the year and press to confirm
ii. Set the month and press to confirm
iii. Set the day and press to confirm
iv. Set the day of the week, press to confirm
3. Press to exit.
1 Date
2 Time
Date
1
XX
Days
MM YY
Day of the week
Time
1
i
3
PM H:M
You will now have to select from the following options: You can either have a manual mode,
automatic mode with 2 settings a day or 4 settings a day.
Manual mode –where the heating will be on for 24 hours or until you turn it off.
Automatic mode with 2 settings - i.e. one heating cycle a day where the heating goes on and
off at your specified times.
Automatic mode with 4 settings where you will have 2 heating cycles a day.
Mode
4
5
3
Switch on the thermostat by pressing the Power button. If power has been applied for the first
time, you will have to set the date and time.
3
i
ii
iii
iv
2
2
ii

1. Press once to select Mode and press to
confirm.
2. Use the arrow keys to select Manual mode
and press to confirm.
3. Use the arrow keys to set the temperature
and press to confirm
4. Press twice to go back to the main screen
Mode
1
2
3
3 Manual
4
24.0 °C
Set
The thermostat comes with pre-programmed schedule for easy and economic heating control
of most homes. Below are the factory settings or the preset schedule for the week. The
schedule for Saturday and Sunday is different.
This schedule can be changed in the Schedule menu.
Wake Up Leave Home Come Home Go to Sleep
5:30 8:00 18:00 21:30
24°C 16°C 24°C 16°C
Pre-programmed schedule

4. Press twice to select Schedule and press to confirm.
The Automatic icon, House # 1 and the current day of the
week will flash.
5. Press to select the day of the week or the whole week
and press to confirm.
6. Set the hour using the arrow keys & press
to confirm. Now set the minutes and press to confirm.
7. Now set the comfort temperature and confirm. It now
switches to House # 2.
House # 2
8. You are now on House 2 –the time the heating switches off.
Adjust the hour using the arrow keys and press to
confirm.
9. Set the minutes using the arrow keys and press to confirm.
10. Now set the economy temperature and confirm.
House # 3
11. Hold the down arrow key until you see 4 dashes for the time
and press to confirm.
House # 4
12. You are now on House 4. Again hold the down arrow key
until you see 4 dashes for the time and press to confirm.
13. Touch the return button twice to go back to the main screen.
Sched
4
4 Automatic mode (2 settings)
1. Press once to select Mode and press to
confirm.
2. Use the arrow keys to select Automatic
mode and press to confirm.
3. Press twice to go back to the main screen.
Mode
1
2
3

4. Press twice to select Schedule and press to confirm.
The Automatic icon, House # 1 and the current day of the week will
flash.
5. Press to select the day of the week or the whole week
and press to confirm.
6. Set the hour using the arrow keys & press
to confirm. Now set the minutes and press to confirm.
7. Now set the comfort temperature and confirm. It now
switches to House # 2.
House # 2 (the time you leave home or to switch off the heating)
8. Adjust the hour using the arrow keys and press to confirm.
9. Set the minutes using the arrow keys and press to confirm.
10. Now set the economy temperature and confirm. It now switches
to House 3.
House # 3 (the time you return home or to switch on the heating)
11. Adjust the hour using the arrow keys and press to confirm.
12. Set the minutes using the arrow keys and press to confirm.
13. Now set the comfort temperature and confirm. It now switches
to House 4.
House # 4 (the time the heating switches off or the time you go to
sleep)
14. Adjust the hour using the arrow keys and press to confirm.
15. Set the minutes using the arrow keys and press to confirm.
16. Now set the economy temperature and confirm.
17. Touch the return button twice to go back to the main screen.
5 Automatic mode (4 settings)
1. Press once to select Mode and press to
confirm.
2. Use the arrow keys to select Automatic
mode and press to confirm.
3. Press twice to go back to the main screen.
Mode
1
2
3

6 Heated towel rail
1. Press three times to select Towel and press to confirm.
2. House # 1 and the time will flash.
3. Press to adjust the hour and press to confirm.
4. Now set the minutes and press to confirm.
6. It will now move to House 2. Set the hour and minutes and
press to confirm.
7. Set the hour and minutes for house 3 and press to confirm.
8. Set the hour and minutes for house 4 and press to confirm.
9. Press twice to exit the user setting and go back to the
main screen.
If you want the towel rail to come on twice a day, set the 2 times and use the
key to set the remaining 2 times to ---- (dash)
The towel rail is programmed to remain on for 3 hours by default. The following table shows
the default setting where the towel rail is ON only twice a day and settings 2 and 3 are blank.
If you would like to change the above settings, follow the steps below:
Setting On Off
Setting 1 5:30 8:30
Setting 2 -- --
Setting 3 -- --
Setting 4 18:00 21:00

1. Press once to select Mode and press to
confirm.
2. Use the arrow keys to select Vacation mode
and press to confirm.
3. Use the arrow keys to set the number of
days you will be away and press to confirm
4. Press twice to go back to the main screen
(Vacation mode is enabled immediately and the floor
will be set to a temperature of 10 degrees until
disabled)
Mode
1
2
3
7 Vacation setting
4
16
1. Press 7 times to select Bright and to
confirm.
2. Use the top and down arrow keys
to adjust the brightness (Range 1-5) and press
to confirm.
3. Press to exit
8 Brightness
Bright
1
2
3
5Set
1. Press 6 times to select Clean and press to confirm.
2. All keys will lock for 10 seconds
3. Press to exit
9 Clean

Engineering Settings
1. Press and hold for 3 seconds to enter the internal setting operation.
2. Use the up and down arrow keys to select the number to change the setting and
press to confirm.
3. Press to leave the internal setting screen.
No Setting Parameter Default
2. Towel Rail Control 0. Towel rail disabled
1. Towel rail enabled 1
3. Control mode
A/F/AF
0. F (Floor sensor)
1. A (Air Sensor)
2. AF (Air Sensor with Floor Limiter)
0
15. Temperature format 0: Deg C
1: Deg F 0
16. Clock format 0: 12 hours
1: 24 hours 0
22. Reset to default
settings
0: No
1: Reset 0
24. Towel rail set time 0-180 mins 180