Warn 75330 User manual

WARN INDUSTRIES PAGE 1 75331 Rev. A0
INSTALLATION INSTRUCTIONS
MULTI-MOUNT KIT
Part Number: 75330
Application: Warn HP PowerPlant P/N 71800
Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have provided
installation and operating instructions and other information on labels and in this guide. This information alerts you to potential
hazards that could hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you
must use your own good judgment.
CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT
DAMAGE. READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS
BEFORE INSTALLING AND OPERATING THIS PRODUCT.
This guide identifies potential hazards and has important safety messages that help you and others avoid personal injury or
death. WARNING and CAUTION are signal words that identify the level of hazard. These signal words mean:
WARNING signals a hazard that could cause serious injury or death, if you do not follow recommendations.
CAUTION signals a hazard that may cause minor to moderate injury, if you do not follow recommendations.
This guide uses NOTICE to call attention to important mechanical information, and Note: to emphasize general information
worthy of special attention.
CAUTION
MOVING PARTS ENTANGLEMENT HAZARD
Failure to observe these instructions could lead to minor or moderate injury.
qAlways take time to fully read and understand the installation and Operations Guide included with
this product.
q Never operate this product if you are under 16 years of age.
qNever operate this product when under theinfluence of drugs, alcohol or medications.
Read installation and operating instructions thoroughly.
WARNING
INJURY HAZARD
Failure to observe these instructions could lead to severe injury or death.
q Always use extreme caution when drilling on any vehicle. Make sure that all fuel lines, brake lines, electrical wires, and other objects arenot
punctured or damaged when/if drilling on the vehicle. Thoroughlyinspect the areatobe drilled (on both sides of material) prior to drilling, and
relocate any objects that may be damaged. Failure to inspect the area to be drilled may result in vehicle damage, electrical shock, fire or
personal injury.
q Always wear safetyglasses when installing this kit. A drilling operation will cause flying metal chips. Flying chips can cause eye injury.
q Always use extreme caution when cutting and trimming during fitting.
q Always remove jewelry and wear eye protection.
q Never lean over battery while making connections.
q Never route electrical cables:
oAcross any sharp edges.
oThrough or near moving parts.
oNear parts that become hot.
q Always insulate and protect all exposed wiring and electrical terminals.
q Always install terminal boots as directed in installation instructions.
q Always inspect the quick connect polarity on the cable from the battery AND the cable from the winch.
q Always use appropriate and adequate care in lifting components into place.
q Always insure components will remain secure during installation and operation.
q Always tighten all nuts and bolts securely, per the installation instructions.
q Always stay clear of moving parts and joints. Always keep others away when operating or adjusting plow.
q Always replace all worn or damaged parts before operating.
q Never operate this WARN product with damaged or missing parts.

WARN INDUSTRIES PAGE 2 75331 Rev. A0
PARTS LIST
Part Number Qty Description
75240 1 Multi-Mount Frame Kit
63063 1 Hitch Pin and Clip
69847 1 Plug, Quick Disconnect
30510 1 Quick Disconnect Cable, 36” Winch
26405 1 Quick Disconnect Cable, 90” Battery
TOOLS REQUIRED
7/16” Wrench (2)
1/2” Wrench
9/16” Wrench
5/8” Wrench
11/16” Socket Wrench
1/4” Drill bit and Drill motor
Correct wrenches for connection to battery termnal
Safety Glasses
TORQUE SPECIFICATIONS 1/4 8 lb. ft..(10.8 N-m)
3/8 30 lb. ft. (40.7 N-m)
7/16 50lb. ft. (67.8 N-m)
BEFORE YOU BEGIN
The WARN Multi-Mount PowerPlant System is to be used only with a WARN Multi-Mount
Front Receiver or a class 3 receiver hitch. When the winch is used at the rear hitch of a vehicle,
use a 20’ (p/n 32963) or 24’ (p/n 32966) WARN Quick Connect Power Cable to extend forward
to the vehicle battery.
1. Before bolting the winch to Multi-Mount Frame, it is necessary to attach the Quick Connect
Cable to the PowerPlant in place of the long red and black battery cables. See Figure 1
NOTICE
EQUIPMENT DAMAGE
q Always refer to the Installation and Specification Guide, supplied in the winch kit, for all wiring
schematics and specific details on how to wire this WARN product toyour vehicle.
Read installation and operating instructions thoroughly.

WARN INDUSTRIES PAGE 3 75331 Rev. A0
Figure 1
Remove the 5/16” bolt securing the ground cable to the bottom of the motor. Note the small
black wires secured by the same bolt. Be sure to reconnect these in the same position when
the new ground cable is installed.
Cut the wire tie securing wires to the terminal boot on the positive cable. Slide the boot down
the cable and remove the nut securing the positive cable to the contactor terminal. Note the
small red wire secured by the same nut. Be sure to reconnect this in the same position when
the new positive cable is installed.
Carefully remove the boot from the positive cable. It will be reinstalled on the new cable.
Find the 36” twin lead Quick Connect Cable and slide the terminal boot over the positive
cable. The positive cable is identified by the white stripe and the “+” symbol printed on the
insulation. Connect the cable and the small red wire to the contactor terminal and tighten the
nut. Slide the terminal boot over the terminal and with one of the wire ties provided, tie the
small red wires around the boot. See Figure 2
Connect the other “leg” of the 36” Quick Connect Cable (negative or ground cable) to the
motor. Remember to install the small black wire. Tighten the bolt.
Black Ground Cable
Small Black Wires
5/16” Ground Bolt
Red Positive Cable
Wire Tie
around
Terminal
Boot
Positive
Contactor
Terminal

WARN INDUSTRIES PAGE 4 75331 Rev. A0
Figure 2
2. Install the air intake hose and filter per the PowerPlant Operator’s Manual. The filter should
be located where the possibility of water or mud entry is minimal. The hose may be shortened
if necessary or it can be used full length and positioned in a protected location when in use.
3. Install the fairlead on the front of the Mult-Mount Frame. See Figure 3
Intake Hose
Fitting
Twin Lead Quick
Connect Cable,
Negative Cable
Twin Lead Quick
Connect Cable,
Positive Cable
Figure 3

WARN INDUSTRIES PAGE 5 75331 Rev. A0
6. Mount the PowerPlant to the Multi-Mount Frame using the instructions and fasteners
provided with the PowerPlant.
FIGURE 4
7. Mount the Quick Connect from the long cable to a suitable location on the vehicle, within
reach of the PowerPlant cable Quick Connect. When routing the cables note the Injury
Hazard Warnings referring to electrical cable routing at the beginning of these
instructions.
A plug is furnished to keep the vehicle Quick Connect clean when not in use. The lanyard can
be attached to one of the cables or to a location of your choice.
WARNING: Always inspect the quick connect polarity on the cable from the battery AND
the cable from the PowerPlant, before connecting the cables to the battery. Make sure the
positive (+) cable exits the side of the plug marked with a “+” symbol, and the negative (-)
ground cable exits the side of the plug marked with a “-” symbol. The positive cable can be
identified by the white stripe and the “+” symbols printed on the insulation. Some positive
cables have red insulation. The ground cable is black.
WARNING
CHEMICAL AND FIRE HAZARD
Failure to observe these instructions could lead to severe injury or death.
•Always inspectthequickconnectpolarityonthecablefromthebatteryANDthecablefromthe
PowerPlant.
8. Connect positive (+) power cable lead (white stripe) to the battery positive (+) terminal and
the (-) lead to the negative (-) terminal. To make battery connection easier Warn has battery
bolt kits available for General Motors vehicles with side terminal batteries (p/n 73761) and
late model Ford vehicles with small terminal bolts (p/n 72720).
9. Upon completion of the installation, check PowerPlant for proper operation.
Quick Connect
Drill two 1/4” holes in the location of
your choice
1/4-20x1 1/2 hex head capscrew
1/4 lock washer
1/4-20 hex nut

WARN INDUSTRIES PAGE 6 75331 Rev. A0
MAINTENANCE/CARE
1. Inspect all parts on the PowerpLant, Multi-Mount Frame, and related hardware prior to each use.
Replace all hardware that appears rusted or deformed.
2. Inspect all nuts and bolts on the PowerPlant, Mult-Mount Frame, and related hardware prior to
each use. Tighten all nuts that appear to be loose. Stripped, fractured, or bent bolts or nuts need
to be replaced.
3. Check all cables prior to use. Replace cables that look worn or frayed.
4. Check all moving or rotating parts. Remove debris that may inhibit the part from moving freely.
WARNING
INJURY HAZARD
Failure to observe these instructions could lead to severe injury or death.
qAlways take time to fully read and understand the vehicle’s operator manual, PowerPlant operator manual and
warning labels prior to operation of PowerPlant.
WARNING
INJURY HAZARD
Failure to observe these instructions could lead to severe injury or death.
qAlways securely tighten all bolts on the Mult-Mount Frame, PowerPlant, and fairlead prior to operation of PowerPlant.
WARNING
INJURY HAZARD
Failure to observe these instructions could lead to severe injury or death.
qAlways perform regular inspections on the PowerPlant, Multi-Mount Frame, and related hardware.
q Always replace all worn or damaged parts before operating.
q Never operate this WARN product with damaged or missing parts.