Wasp WLS 9500 User manual

QUICK START GUIDE
Wasp WLS 9500
www.waspbarcode.com

Quick Start Guide
1
CORD ATTACHMENT
Scan Window
Trigger
LED
Beeper
Interface cable
modular connector
To host
Cable
interface
Interface cable
modular connector clip
Model Number and
Serial Number appear
here.

Quick Start Guide
2
SCANNER PROGRAMMING BARCODES
Reset Defaults
Set All Defaults
Set Postamble
Note: If you do not need a Postamble, scan 1 Erase All Rules.
*Default Setting
1 Erase All Rules
Erase All Rules
2 Begin New Rules
Begin New Rules
3 Send All Data
Send All Data
Enter
TAB
5 Save All Rules
Save All Rules

Quick Start Guide
3
HOST INTERFACES
Note: Cable may vary depending on configuration.
SCANNER PROGRAMMING BARCODES
Start Here if you have a USB scanner:
*HID Keyboard Emulation
USB OPOS Handheld
Start Here if you have a keyboard wedge scanner.
IBM PC/AT and IBM PC Compatible
IBM AT Notebook
Must be PS2 Port
Keyboard Wedge
Must be powered USB
port.
USB

Quick Start Guide
4
TROUBLESHOOTING
Scanner not working Scanner not decoding barcode
No power
to scanner
Incorrect
interface
cable
used
Interface/power
cables are
loose
Scanner not
programmed
for barcode
type
Barcode
unreadable
Distance
between
scanner
and
barcode
incorrect
Check
system
power;
ensure
power
supply, if
required,
is
connected.
Ensure
that
correct
interface
cable is
used
Check for
loose cable
connections
Program the
scanner to
read that
type of
barcode.
Ensure
barcode is
not
defaced;
try
scanning
test
barcode of
same
barcode
type
Move
scanner
closer to
or
further
from
barcode
Scanner decoding barcode, but data
not transmitting to host
No keyboard connected
Scanner not
programmed for
correct host
interface
Interface cable is
loose
A keyboard is not being used with this
device.
Check scanner
host parameters
or edit options
(The scanner
host barcodes
are provided
below in the
Start Here if you
have a USB
scanner section
and the Start
Here if you have
a keyboard
wedge scanner
section.)
Check for loose
cable connections
Scan the IBM AT NOTEBOOK
barcode (This barcode is provided
below in the Start Here if you have a
keyboard wedge scanner section.)
Problem
Resolution
Problem
Resolution
Possible Cause
Possible Cause

Quick Start Guide
5
SYMBOLOGIES
This section provides the following information:
Enable/Disable Barcodes - These barcodes allow you to enable or disable symbologies.
Check Digit Barcodes - The check digit is the last character of the symbol used to verify the integrity
of the data. It is always verified to guarantee the integrity of the data (applies to UPC-A/UPC-E and
Code 39 only).
Preamble Barcodes - Preamble characters are part of the UPC symbol consisting of Country Code
and System character. Three options are given for transmitting UPC-A preamble to the host device:
transmit System Character only, transmit System Character and Country Code ("0" for USA) and no
preamble transmitted (applies to UPC-A/UPC-E only).
Conversion Barcodes - Allow you to convert UPC and Code 39 barcodes.
*Denotes default value
UPC/EAN
Enable/Disable UPC-A/UPC-E
*Enable UPC-A
Disable UPC-A
*Enable UPC-E
Disable UPC-E

Quick Start Guide
6
Enable/Disable UPC-E1
Enable/Disable EAN-13/EAN-8
Enable UPC-E1
*Disable UPC-E1
*Enable EAN-13
Disable EAN-13
*Enable EAN-8
Disable EAN-8

Quick Start Guide
7
Enable/Disable Bookland EAN
Transmit UPC-A Check Digit
Enable Bookland EAN
*Disable Bookland EAN
*Transmit UPC-A Check Digit
Do Not Transmit UPC-A Check Digit

Quick Start Guide
8
Transmit UPC-E1 Check Digit.
UPC-A Preamble
*Transmit UPC-E1 Check Digit
Do Not Transmit UPC-E1 Check Digit
No Preamble
(<DATA>)
*System Character
(<SYSTEM CHARACTER> <DATA>)
System Character & Country Code
(< COUNTRY CODE> <SYSTEM CHARACTER> <DATA>)

Quick Start Guide
9
UPC-E Preamble
UPC-E1 Preamble
No Preamble
(<DATA>)
*System Character
(<SYSTEM CHARACTER> <DATA>)
System Character & Country Code
(< COUNTRY CODE> <SYSTEM CHARACTER> <DATA>)
No Preamble
(<DATA>)
*System Character
(<SYSTEM CHARACTER> <DATA>)
System Character & Country Code
(< COUNTRY CODE> <SYSTEM CHARACTER> <DATA>)