Wasserstein 3-in-1 Smart Floodlight, Charger & Mount for Blink Outdoor & Blink XT... User manual

USER MANUAL
Sensor
3-in-1 Smart Floodlight, Charger
& Mount for Blink Outdoor
& Blink XT 2

In the Box
Safety Information
Page 2
• Disassembling the light head may cause damage to internal components.
The floodlight may not function properly after disassembly.
• Turn OFF the main circuit before installation.
• DO NOT remove the protective LED lens.
• DO NOT look directly at LEDs that are turned on.
• DO NOT leave bare wires exposed outside the wall canopy enclosure.
Smart
floodlight
Screws Wire nuts
EVA gasket
USB cable
Camera mount
adapter
CrossbarScrew cap
1. Make sure you have all the included
materials.
2. You will be working with electrical wires
during the installation process. For safety
reasons, shut off the power to your floodlight
at the circuit breaker.
Pre-installation
Note: If you are unfamiliar with electrical installations, we highly recommend
hiring a professional electrician to perform the installation.
Installation

If You Have an Existing Floodlight
1. Remove your existing floodlight from the junction box and disconnect the
wires.
Page 3
2. Remove the crossbar attached to your junction box.
3. Secure the ground wire.

Page 4
Installing the Floodlight to the Junction Box
1. Attach the crossbar included in the package to the junction box with the
screws.
a. Remove the protective tape from the EVA gasket. Press the adhesive side
firmly against the rear of the floodlight.
2
b.Ensure that the center screw hole and wire slot of the foam gasket are
aligned with the screw hole and wire slot.
2
3. Before securing the cover of your junction box, thread the wires through
the slot on the bottom of the plate to access them during installation.
Junction Box

1. Connect the green and yellow wire from the floodlight to the existing
ground wire inside the junction box. Use the included wire nut to connect
the wires properly.
2. Using a wire nut, connect the white neutral wire from the floodlight to the
neutral wire of the junction box.
3. Using a wire nut, connect the black hot wire from the floodlight to the hot
wire of the junction box.
The white wire on your floodlight is a neutral wire.
The black wire on your floodlight is a hot wire.
Wiring the Floodlight and Junction Box Through the EVA Gasket
Page 5
Neutral Wire (White)
Hot Wire
(Black)
Ground Wire
(Copper)
Junction Box
Wire Nuts
Important: Before mounting the floodlight, completely apply the EVA gasket around the
perimeter of the cover plate where the back of the cover plate meets the mounting surface.
This prevents water from seeping into the junction box.
a. Make sure the wire connections are secured. Carefully place the wires
into the junction box.
4
4
b.Mount the floodlight onto the crossbar and secure it with the screw cap
provided.
5. Check the wirings are installed correctly by switching on the floodlight.

Page 6
Minimum requirements:
• Smartphone or tablet running iOS 9.0 or later / Android 5.0 or later.
• 2.4Ghz WiFi Network (not compatible with 5GHz connections).
• Upload speed of at least 2 Mbps.
1. Download the App
Download the app by scanning the QR code or by searching "Wasserstein App"
in Google Play Store or the App Store.
2. Sign Up/Login
Sign up for a new account or Login into an existing account.
3. Adding your device
Click “Add Device” or “+” at the top right corner to enter add device page.
There are two ways of adding devices: “Add Manually” and “Auto Scan”.
App Setup
App Store Google Play Store

1. Select “Lighting” - “PIR Light（BLE+Wi-Fi)”
2. Power on the device, follow the steps displayed as shown on your app
(Picture 2) Your floodlight will dim and flash in intervals. (Figure 1)
Page 7
Manual Scan
Figure 1
selection
Flash Flash
Dim Dim

3. Enter your Wi-Fi details, and click "Next".
4. Wait until your device has been successfully scanned.
Wasserstein Smart Floodlight
Page 8
WiFi Login
WiFi Password

Page 9
Auto Scan:
1. Enable pairing mode for your floodlight.
2. Wait until your floodlight has been automatically detected.

Note: Display and interface are subject to change.
4. App Functions
Sensor
Manual
On/Off
Light Intensity
Floodlight Color
Turn-off Timer
Schedule
Sensor
On/Off
Motion Detection Range
Floodlight Light Sensitivity
Duration of Light Flash
Event Records
Page 10

5. How to Use Linked Devices
You can control other devices through ‘Linked Devices’. On the "Sensor" page
click on "Linked Devices"，Then click "+" on the lower right corner to enter the
"Create new Smart" page. Here you can add multiple trigger conditions and
tasks to perform.
Page 11

Page 12
6. Third-party Control (Google Assistant & Amazon Alexa)
Follow the instructions inside to link your home assistant.
Example of voice commands is also available in the App.

Page 13
1. To charge your camera via the floodlight, plug in the USB cable at the
micro-USB port of the camera. Press in firmly.
2. Insert the Blink camera mount adapter.
3. Screw the camera onto the mount.
4. Open the USB port cap of the floodlight and connect the cable. Press in
firmly.
5. Adjust the camera to your preferred viewing angle.
Mounting Screw
Charging Port
Mounting Your Camera (Blink Outdoor & Blink XT2)
1. Assess where intruders are most likely to enter and the path they would take.
Most intruders enter homes through a back door, patio door, or garage
door. Therefore, it is advisable to place the floodlight near the entrances to
your home.
2. Mount the floodlight on walls that an intruder would walk alongside, such as
a narrow pathway. The motion sensor works best when movements are
detected parallel to the floodlight, not towards it.
3. You can also mount the floodlight beside your security camera to illuminate
the camera’s vision at night.
4. Although the floodlight is weatherproof, it is advisable to mount it to a wall
shaded from the rain and sunlight to maximize battery life.
5. Due to continuous product improvement, all App settings above are subject
to change without prior notice. Please always keep the App updated to the
latest version.
Important Tips
1.The smart floodlight will not turn on. What's going on?
There are several possibilities. Try the following steps.
FAQ
• Check your connection to the house’s power.
• Leave the area for 10 minutes to give time for the floodlight to reset
without you triggering it. Return and check the floodlight by turning off the
power for at least a minute, then turning it back on.
• Make sure you are testing the floodlight at night.
• Make sure the App is installed and paired with your smart floodlight
correctly.

Materials: PC + Aluminum
Sensor angle range: 120°
Sensor distance thresholds: 13 to 33 ft (4 to 10 m)
Max LED light intensity: 1500 Lumens
Color temperature: 3000 - 6500 K
Power: AC 120V
Frequency: 2.4GHz
Product Specifications
For more information, visit:
www.wasserstein-home.com
or contact us at:
[email protected]
Made in China
Blink Outdoor is not included. Blink XT2 is not included.
Wasserstein is not affiliated with Immedia Semiconductor Inc.
Wasserstein is a trademark of Dropcases Ltd. Blink Outdoor is
a trademark of Immedia Semiconductor Inc. Blink XT2 is a
trademark of Immedia Semiconductor Inc.