Wasserstein Floodlight with Charger User manual

The Wasserstein Wired Floodlight & Charger with Integrated Mount for
Ring Spotlight Cam Battery and Stick Up Cam Battery is an ideal solution to enhance
your camera’s vision in low light outdoor conditions.
Floodlight with Charger
Compatible with Ring Spotlight Cam Battery and
Stick Up Cam Battery
User Manual

Table of Contents
Page 1 - 8
Package Includes 2
Safety Information 2
Features 2
Installing Your Floodlight 3
Mounting Your Camera 6
Important Tips 7
FAQ 7
Specications 7
Need help? Send us an email at: [e-mail]

Package Includes
Page 2 - 8
• 1 x Floodlight
• 2 x Screws
• 1 x USB Cable
• 1 x Screw Converter (for Spotlight Cam)
• 1 x Wrench
• 1 x User Manual
• 1 x Crossbar
• 1 x Screw Cap
• 3 x Wire Nuts
• 1 x EVA Gasket
Safety Information
• Disassembling the light head is not recommended as it may cause damage to
internal components. The oodlight may not function properly after disassembly.
• Turn the main circuit OFF before installation.
• Do NOT remove the protective LED lens.
• Do NOT look directly at LEDs that are turned on for any length of time.
• Do NOT leave bare wires exposed outside the wall canopy enclosure.
Feature
PIR Motion
Detection
IP65 Waterproof Universal Female
USB Charging
Integrated
Mount
Floodlight
Screws
Wire Nuts
EVA Gasket
Wrench
Screw Converter
Crossbar
Screw Cap
USB Cable
Need help? Send us an email at: [e-mail]

1. Make sure you have all the included materials.
2. You will be working with electrical wires during
the installation process. For safety reasons, shut
o the power to your oodlight at the circuit
breaker.
If You Have an Existing Floodlight
1. Remove your existing oodlight from the junction box, and disconnect the wires.
If there is a crossbar attached to your junction box, remove it also.
2. Remove the crossbar attached to your junction box.
Page 3 - 8
Installing Your Floodlight
Preinstallation
Note: If you are unfamiliar with electrical installations, we highly recommend hiring a
professional electrician to perform the installation.
Need help? Send us an email at: [e-mail]

Page 4 - 8
Installing Your Floodlight
Installing the Floodlight to the Junction Box
1. Attach the crossbar included in the package to the junction box with the screws.
3. Secure the ground wire.
a. Remove the protective tape from the EVA gasket. Press the adhesive side rmly
against the rear of the oodlight.
2
b. Ensure that the center screw hole and wire slot of the foam gasket are aligned
with the screw hole and wire slot.
2
Need help? Send us an email at: [e-mail]

3. Before securing the cover of your junction box, thread the wires through the slot
on the bottom of the plate to access them during installation.
1. Connect the green and yellow wire from the oodlight to the existing ground
wire inside the junction box. Use the included wire nut to connect the wires
properly.
2. Using a wire nut, connect the white neutral wire from the oodlight to the neutral
wire of the junction box.
3. Using a wire nut, connect the black hot wire from the oodlight to the hot wire of
the junction box.
The white wire on your oodlight is a neutral wire.
The black wire on your oodlight is a hot wire.
Wiring the Floodlight and Junction Box Through the EVA Gasket
Installing Your Floodlight
Page 5 - 8
Neutra Wire (White)
Hot Wire (Black)
Ground Wire
(Copper)
Junction Box
Wire Nuts
Junction Box
Need help? Send us an email at: [e-mail]

Page 6 - 8
Installing Your Floodlight
Mounting Your Camera (Ring Spotlight Cam Battery)
1. To charge your camera via the oodlight, remove the charging port cap of the
camera and connect the oodlight’s charging cable. Press in rmly.
2. Screw the screw converter into the Ring Spotlight Cam Battery.
3. Screw the camera onto the mount.
4. Open the USB port cap of the oodlight and connect the charging cable. Press in
rmly.
5. Take out the mounting wrench and adjust the Ring Spotlight Cam to your desired
angle.
Mounting Screw
Charging Port
Need help? Send us an email at: [e-mail]
5. Switch on the electricity, checking that the wiring
has been done correctly and that the oodlight
turn on.
Important: Before mounting the oodlight, completely apply the EVA gasket around the perimeter of the
cover plate where the back of the cover plate meets the mounting surface. This prevents water from
seeping into the junction box.
Note: The oodlight will provide continuous charging to the USB port
24/7, however, the motion sensor will only get triggered and turn the
lights on when it is dark outside (i.e., during night time).
a. Make sure the wire connections are secured. Carefully place the wires into the
junction box.
4
4
b. Mount the oodlight onto the crossbar and secure it with the screw cap provided.

Important Tips
FAQ
Page 7 - 8
1. Assess where intruders are most likely to enter and the path they would take.
Most intruders enter the home through a back door, patio door, or garage door.
Therefore, it is advisable to place the oodlight near entrances to your home.
2. Mount the oodlight on walls that an intruder would walk alongside, such as a
narrow pathway. The motion sensor works best when movements are detected
parallel to the oodlight, not towards it.
3. You can also mount the oodlight beside your security camera to illuminate the
camera’s vision at night.
4. Although the oodlight is weatherproof, it is advisable to mount it to a wall
shaded from the rain and sunlight to maximize battery life.
• Check your connection to the house power.
• Check the area around the oodlight. There may be something in the area (e.g. a
small animal) that is triggering it.
One or more oodlight(s) is ashing on and o. What's going on?
There are several possibilities. Try the following items:
Mounting Your Camera (Stick Up Cam Battery)
1. To charge your camera via the oodlight, remove the charging port cap of the
camera and connect the oodlight’s charging cable. Press in rmly.
2. Screw the camera onto the mount.
3. Open the USB port cap of the oodlight and connect the charging cable. Press in
rmly.
Mounting Screw
Charging Port
Need help? Send us an email at: [e-mail]

• Check your connection to the house power.
• Leave the area for 10 minutes to give time for the oodlight to reset without you
triggering them. Return and check the oodlight by turning o the power for at
least a minute, then turning it back on.
• Make sure you are testing the oodlight in darkness.
A oodlight will not turn on. What's going on?
There are several possibilities. Try the following items:
Plastic Material : PC + Aluminum
Sensor Angle Range : 120°
Sensor Distance Thresholds : 13 to 33 ft (4 to 10 m)
Max LED Light Intensity : 2000 Lumens
Color Temperature : 5500 - 6500 K
Power : AC 120V
Ring Spotlight Cam Battery not included.
Ring Stick Up Cam Battery not included.
Wasserstein is not aliated with Ring, Inc.
Wasserstein is a trademark of Dropcases Ltd.
Ring Spotlight Cam Battery is a trademark of Ring, Inc.
Ring Stick Up Cam Battery is a trademark of Ring, Inc.
For more information, visit:
www.wasserstein-home.com
or contact us at:
[email protected]
®
Made in China
FAQ
Specication
Page 7 - 8
Need help? Send us an email at: [e-mail]